aluminum alloy
Coatings Applied Onto 7075 Aluminum Alloy
... powders were used for spraying a bond coat (BC) and a top coat (TC), respectively, onto a 7075 aluminum alloy substrate. The effect of acetylene-to-oxygen ratio and the spraying distance on surface ...
12
Numerical simulation of the bulk forming processes for 1345 aluminum alloy billets
... In the present work this parameter (plastic flow) will be identified by a torsion test for which the plastic deformation zone is higher than in a tensile test. Thus, the torsion test was carried out on specimens of 1345 ...
9
Fatigue crack growth analysis of pre-strained 7475–T7351 aluminum alloy
... Aluminum alloy plate of 7475–T7351 with a thickness of 76.2 mm was used in this study. The chemical composition is shown in Table 1. Strips of 6 mm thickness, shown in Fig. 1, were machined from the ...
9
Characterization And Study of Friction Stir Welding of AA6101 Aluminum Alloy
... Friction stir welding (FSW) combines two plates by frictional heating at the interface with the localized plastic deformation within the material. In friction stir welding heat is generated by the friction between ...
4
Studies on the effect of vibration on hot cracking and Grain size in AA7075 Aluminum alloy Welding
... strength Aluminum alloy ...strength aluminum alloys is formation of hot cracking. When Aluminum alloy is welded by GTAW process, weld fusion zone shows coarse columnar grains during ...
6
Microstructure Evolution and Properties of Friction Stir Welding Joint for 6082-T6 Aluminum Alloy
... 6082-T6 aluminum alloy can be used as a new lightweight material instead of traditional steel material for application in the transportation and structural engineering industry, and can reduce weight and ...
10
A Comparative Study of the Heat Input During Laser Welding of Aeronautical Aluminum Alloy AA6013-T4
... strength aluminum alloy AA6013-T4 was evaluated from macrostructural and microstructural points of ...liquid aluminum changed largely with experimental conditions, from ...
12
The Effect of Casting Speed and the Fraction of Al5Ti1B Inoculant on the Microstructure and Mechanical Properties of the AA5052 Aluminum Alloy Produced by the Direct Chill Process
... AA5052 aluminum alloy plate manufactured by the Direct Chill ...the alloy mechanical properties and on their performance in rolling process was also ...AA5052 alloy rolling ...
11
Solidification behavior and rheo-diecasting microstructure of A356 aluminum alloy prepared by self-inoculation method
... A356 aluminum alloy semisolid slurry after holding at 600 °C for 0 min, 3 min, 5 min and 10 min, ...A356 aluminum alloy containing rose- shape and ine dendritic primary particles can be ...
9
The Effect of Casting Speed and the Fraction of Al5Ti1B Inoculant on the Microstructure and Mechanical Properties of the AA5052 Aluminum Alloy Produced by the Direct Chill Process
... AA5052 aluminum alloy plate manufactured by the Direct Chill ...the alloy mechanical properties and on their performance in rolling process was also ...AA5052 alloy rolling ...
11
Corrosion resistance of 2024 aluminum alloy coated with plasma deposited a-C:H:Si:O films
... 2024 aluminum alloy is widely employed in aeronautic and automobilist ...2024 aluminum alloy as well as the corrosion resistance of the ilm/substrate systems under different corrosive ...the ...
17
Thermal Stability and Microstructure of Nanometric 2024 Aluminum Alloy Powder Obtained by Cryogenic Milling and Spark Plasma Sintering
... 2024 aluminum alloy used was ...Al alloy powder was processed by cryomilling in liquid nitrogen without the use of a process control agent (PCA; such as methanol, stearic acid and/or paraffin ...
10
Statistical modeling of fatigue crack growth rate in pre-strained 7475-T7351 aluminum alloy
... Fatigue crack growth rate in pre-strained 7475-T7351 alu- minum alloy plate was evaluated in air and at room temperature under constant amplitude loading at stress ratios of 0.1 and 0.5, using compact tension ...
11
Influence of control parameters on the crack paths in the aluminum alloy 2024 under bending
... he material tested is aluminium alloy 2024, characterised by low resistance to oxidation, non-weldability and average workability. This material is used to make shafts, screws, pistons, couplings, hydraulic valves ...
8
Thin films produced on 5052 aluminum alloy by plasma electrolytic oxydation with red mud-containing electrolytes
... as aluminum, titanium and ...of aluminum oxide coatings, rapid dissolution of aluminum could be achieved with NaCl, NaOH, NaClO 3 , HCl, and NaNO 3 solutions 6 ...
6
Length Scale of the Dendritic Array Tailoring Strength of a 5052 Aluminum Alloy
... 5052 aluminum alloys, higher Mg content in the interdendritic liquid was capable to generate more instability of the front initially formed by dendrite primary ...the alloy containing ...
9
Mechanical Pretreatment of Surface of Aluminum Alloy D16-T by Shot Peening
... Abstract: The paper describes the influence of shot-peening onto aluminium alloy D16-T surface. There are estimates focusing into microgeometry of the shot peened surfaces, their roughness and a size of selected ...
8
Heat input effect of friction stir welding on aluminium alloy AA 6061-T6 welded joint
... The paper deals with the heat input and maximum temperature developed during friction stir welding with different parameters. Aluminum alloy (AA 6061-T6) has been used for experimental and numerical ...
6
Macro and Micro Structural Characteristics of Dissimilar Friction Stir Welded AA7075 T651-AA6061 T651 Butt Joint
... Abstract— This paper reports the effect of welding parameters on the macro and micro structural characteristics of friction stir welded butt joints of dissimilar aluminum alloy plates between AA7075-T651 ...
5