Epoxy resin
Mechanical properties and morphological characteristics of ARALL reinforced with TRGO doped epoxy resin
... Mechanical properties in tension, bending, fatigue and lap-shear in two different proportions (0.5%wt and 1%wt) of TRGO (Thermally Reduced Graphite Oxide) doped ARALL (Aramid Aluminium Laminate) were examined. The ...
13
Synthesis of Graphene Oxide and Functionalized CNT Nanocomposites Based on Epoxy Resin
... ABSTRACT: Lately, nanomaterials have been largely studied as reinforcements for epoxy resin. Although their usage is highly promising, the literature has reported some drawbacks regarding the improvement of ...
10
Physical and Mechanical Characterization of Artificial Stone with Marble Calcite Waste and Epoxy Resin
... this epoxy resin together with the load of calcite generates a high-performance product with excellent properties, providing both environmental solutions for waste as benefits ...
6
Mechanical properties and morphological characteristics of ARALL reinforced with TRGO doped epoxy resin
... Point A in Figure 1 shows the linear behaviour in the elastic range of deformation of the material up to the yield point. Plastic deformation continues up to point B, where deformation hardening decreases to a lower ...
13
Effect on the reactive diluent PGE on the cure kinetics of an epoxy resin used in structural composites.
... AN EPOXY RESIN USED IN STRUCTURAL ...in epoxy resins formulations in order to increase the toughness of the epoxy molded ...the epoxy resin, it was used in concentrations of 2,5; ...
6
Epoxy Resin Based Composites, Mechanical and Tribological Properties: A Review
... of epoxy resin based composites ...of epoxy resin based composites using parameter such as sliding speed, sliding distance, applied load, specific wear rate and mass ...of epoxy ...
25
Mat. Res. vol.19 número4
... An infrared spectrometer, Nicolet 380, was used to study the FTIR spectra of ferrosilicon particles to determine whether new chemical bonds are generated before and after modiication via silane coupling agent and coating ...
6
J. Braz. Chem. Soc. vol.17 número6
... for 2 h. The cured samples (about 1 g) were milled and treated with hot toluene to extract the rubber component that was not chemically bonded to the epoxy matrix. The CPBER sample presented an amount of soluble, ...
7
Polímeros vol.23 número1
... DGEBA (Araldite GY 279) and a hardening agent (polyamidoamine adduct – Aradur 2963) manufactured by Huntsman were used to obtain the epoxy resin. The plowed Araldite GY 279 and Aradur 2963 were analyzed ...
5
J. Aerosp. Technol. Manag. vol.9 número2
... Multi-layered RAS are based on materials responsible for dielectric losses (Lee et al. 2016) and/or magnetic losses (Xu et al. 2016). Several investigations on multi-layered dielectric structures have been reported in ...
10
Mechanical Characteristics of Rattan Reinforced Fiberglass and Epoxy Composites for Shank Prosthesis Application
... using epoxy resin and fiberglass is proven to increase the tensile ...using epoxy resin reinforced with fiberglass has managed to increase the tensile strength of rattan, which is projected as ...
8
Mat. Res. vol.14 número3
... an epoxy resin under rubber addition by means of fractographic analysis and its relation with the fracture process and increase of strength of a composite riser employing this polymeric ...an epoxy ...
12
Mat. Res.
... the resin throughout the entire curing ...commercial epoxy resin formulation widely used as a matrix for thermoset composites, which was submitted to a pre-established and validated curing ...
7
The Carbon Nanotubes Effect into Single-lap Joint Failure Modes and Load Capacity: a Macromechanical Analysis
... (epoxy resin) thickness and the dispersions of non-functionalized carbon based nanostructures (carbon nanotubes - CNT) on mechanical properties of single-lap bonded ...
10
Back to the edge: relative coordinate system for use-wear analysis
... Use-wear studies rely heavily on experiments and reference collections to infer the function of archeological artifacts. Sequential experiments, in particular, are necessary to understand how use-wear develops. ...
12
Mat. Res. vol.18 número6
... with epoxy resin by means of DSC ...pure epoxy resin (PCB0), PCB33, and PC B66 reacted and formed uniform ...of epoxy composites because of high temperature resistance of ...the ...
9
CHARACTERIZATION AND PRODUCTION OF CONDUCTIVE FILLER FROM OIL PALM ASH AND ITS PERFORMANCE IN EPOXY MATRIX
... resin. Aldrahem et. al., 2009 fabricated a functional paint for vibration monitoring by dispersing carbon black (CB) nanoparticulate in epoxy resin. Cochrane et al., 2007 developed a flexible strain ...
8
J. Braz. Chem. Soc. vol.17 número7
... of epoxy resin was subsequently added to this mixture in a mortar and mixed for at least 20 min to produce the final biocomposite, that was packed (330 mg) into the tip of a 1 mL insulin plastic syringe and ...
5
Braz. Dent. J. vol.20 número1
... experimental epoxy-resin and calcium hydroxide-based cement (MBPc), gray mineral tri- oxide aggregate (MTA) and white mineral trioxide aggregate (WMTA) using the agar overlay method with neutral red ...
5
bor 30 1 BOR 2016vol300050
... hypothesis tested was that different drying protocols of the root canal would not affect the apical sealing and bond strength of calcium hydroxide-based and epoxy resin-based sealers.[r] ...
7