Eutectic alloy - Mechanical properties
Microstructural evolution and mechanical properties of Sn-Bi-Cu ternary eutectic alloy produced by directional solidification
... works on low solute content (Cu) Sn-based alloys 8,23-31 . Nevertheless, there has been only a limited amount of data about the mechanical properties of directionally solidified high solute content (Cu) ...
10
Microstructure, phases morphologies and hardness of a Bi–Ag eutectic alloy for high temperature soldering applications
... lent mechanical properties may be achieved with appropriate ...wt%Ag eutectic so that a large range of cooling rates ( _T) could be obtained under unsteady-state ...the eutectic Bi–Ag are ...
10
Effect of Multipoint Sequential Water Mist Cooling of Casting Die on Microstructure and Mechanical Properties of AlSi11 Alloy
... the eutectic precipitates β phase is more refined in the boundary layer ...fine eutectic α+β (transient ...of eutectic precipitates in the transition layer of the core is ...
6
Effect of Bead Overlapping on the Microstructure and Mechanical Properties of CoCrWC Alloy Coatings
... Moreover, wear evaluation also confirmed important differences, which can be directly associated with microstructure (seeFigs. 12 and 13). Higher mass loss rate was measured for 180 deposition current, associated with ...
7
Study of Mechanical and Wear Behaviour of Hyper-Eutectic Al-Si Automotive Alloy Through Fe, Ni and Cr Addition
... base alloy increases the wear rate due to the formation of needle beta ...the alloy does not impede formation of needle-like intermetallic compounds and has no positive effect on the modification of ...
9
Influence of aging modes on microstructure and mechanical properties of AZ80 magnesium alloy
... equilibrium solidification, distributed along the grain boundary with block-like or island shapes, only the small amount of them formed within α-Mg matrix. The eutectic structure occurs in the grain boundary as ...
4
Microstructural and mechanical properties of gravity-die-cast A356 alloy inoculated with yttrium and Al-Ti-B grain refiner simultaneously
... better mechanical properties of tensile strength and ...the eutectic silicon phase and the grain boundary becomes narrow and ...silicon eutectic phase into a more fibrous form as compared with ...
6
Effect of Overageing Conditions on Microstructure and Mechanical Properties in Al–Si–Mg Alloy
... Al alloy contains proeutectic Al solution, eutectic mixture of Al and Si, Al oxide due to oxidation at higher temperature and precipitataed ...the alloy is solution treated, almost all particles get ...
5
The modification process of AlSi21CuNi silumin and its effect on change of mechanical properties of the alloy
... as eutectic or primary ones. Perfect sliding properties and high abrasion resistance of hypereutectoid silumins result from their structure, which can be characterized by precipitations of primary crystals ...
4
Microstructure and mechanical properties of a compound reinforced Mg95Y2.5Zn2.5 alloy with long period stacking ordered phase and W phase
... with alloy A, the grain size of α-Mg in alloy B is iner and the grain boundaries are ...in alloy A are developed, as shown in ...in alloy B, and the growth of secondary dendrites is limited, ...
5
Effect of Process Parameters on Microstructure and Mechanical Properties of Friction Stir Welded Cast Nickel Aluminum Bronze Alloy (C95800)
... combination of higher axial load with any welding speed and rotation speed causes plastic deformation in the material. The shoulder force is directly responsible for the plunge depth of the tool pin into the work piece ...
13
Mechanical properties of a silicone for high temperature applications
... In this experimental work the thick-adherend shear test was used to enable the measurement of the shear properties of the adhesive according to the standard ISO 11003-2:1993 [29]. The TAST is preferred for ...
97
PVA/polysaccharides blended films: mechanical properties
... specific mechanical features are required. In general, the mechanical properties of the films produced by blending PVA with CG were similar to those of the MBO (Table 1), whereas films ...
7
Mechanical Properties of the Temporal Muscle
... the mechanical importance of this is that the planar network will be very complaint in tension along the fibber direction and can easily deform to follow changing muscle lengths in vivo which potentially could ...
164
Mechanical properties of stent-graft materials
... Currently, an ideal stent-graft can be described as being biocompatible, non-toxic and non-carcinogenic. It has a stable configuration, and it is flexible, conformable and durable. Regarding the mechanical ...
34
Mechanical properties of microsphere based composite materials
... 3.1.1 Conventional Method: The metal spheres were spread inside a cardboard mold box and then the resin was poured over the spheres. The resin was prepared by mixing 90% (by volume) of Biresin LS epoxy with 9 - 11% of ...
59
Mechanical properties of Raphanus sativus L. seeds
... Therefore, mechanical characteristics have been studied to predict seed characteristics as a function of moisture content and temperature under different types of stress (LIU et ...
6
Thermal and mechanical properties of PVDF/PANI blends
... elastic region). Additionally, the elastic region also becomes larger with the increase of the PANI percentage in the blend (changing from 2.5 to 4%), although the value of E does not change. This suggests PANI is ...
6
Effect of Scroll Pin Profile and Tool Rotational Speed on Mechanical Properties of Submerged Friction Stir Processed AZ31B Magnesium Alloy
... within the processed region arising as a result of severe and rapid deformation, while sound stir zones (SZ) were obtained by all the applied pin designs. The SZ consisting fine grains with an interface between stir and ...
9
Mechanical Properties of Electrolyte Jet Electrodeposited Nickel Foam
... nickel-base alloy foam is used to make the electrode material of alkaline water electrolysis, it has better catalytic activity of hydrogen evolution compared with pure nickel, and its strength and potential ...
4