High temperature mechanical properties
Intercritical Heat Treatment Temperature Dependence of Mechanical Properties and Corrosion Resistance of Dual Phase Steel
... Work hardening of the metals can be good indicated by the stain herdening exponent (n). The higher value of 'n' shows the higher rate of materials work hardening. The material with a high value of 'n' is preferred ...
10
Mat. Res. vol.20 número1
... this temperature, the mechanical properties of the composite, especially the elongation and the hardness, are actually not so high due to the incompactness of the ...the temperature ...
13
Res. Biomed. Eng. vol.31 número4
... are high osteoinductive and angiogenic potentials, biological safety, biodegradability, bone-like mechanical properties, and reasonable ...drying temperature and period of drying (3, 24, 48 ...
9
Mechanical properties of ultra-high pressure sintered sphene (CaTiSiO5)
... coefficients in contrast to HAP and CaSiO 3 coatings [3]. Research involving sphene/titania coatings started a decade ago and in one of the recent findings it was exemplified that the heat-treated sphene/titania coatings ...
4
Mat. Res.
... the mechanical properties of the two steels (maraging 300 and SAE 4340) in the conditions in which they show higher ...with high austenitizing temperature shows the best mechanical ...
8
Influence of Austenitizing on the Mechanical Properties of Maraging 300 and Sae 4340 Steels – Comparative Study
... austenitizing temperature range for commercial heat treatments must be high enough to homogenize the austenite, but low enough to avoid the austenite grain ...
9
STUDY OF MECHANICAL PROPERTIES IN A WELD BEAD OF DISSIMILAR METALS
... different properties of metals in order to maximize the performance with minimum ...welding, high energy density beam welding, brazing, and ...for high production & special ...melting ...
6
Rev. IBRACON Estrut. Mater. vol.3 número4
... to high temperatures were rapidly cooled and others were slowly cooled (to room ...the mechanical properties under investigation following concrete rehydration – after a possible reduction from the ...
8
Rev. IBRACON Estrut. Mater. vol.10 número4
... UHPFRC properties and in the development of design ...unique properties (high ductility, low permeability, very high strength capacity in compression, higher toughness) in comparison to ...
15
Investigation on Friction and Wear Properties of High-Temperature Bearing Steel 9Cr18Mo
... a mechanical drawing of the basic frictional pair sample for the room temperature friction and wear ...during temperature changes was determined. The 9Cr18Mo sample size for the high ...
8
Predicting ADI mechanical properties
... - EN – GJS – 800 – 8, - EN – GJS – 1000 – 5, - EN – GJS – 1200 – 2, - EN – GJS – 1400 – 1 From the table 3 results that high-strength grades (1200, 1400 MPa) can be obtained by quench hardening according ...
8
STEEL MECHANICAL PROPERTIES EVALUATED AT ROOM TEMPERATURE AFTER BEING SUBMITTED AT FIRE CONDITIONS
... critical temperature and on the cooling process ...its mechanical properties after being subjected to metallurgic ...with high thermal gradients at elevated temperatures that may produce ...
8
NANOCOMPOSITE POWDERS FOR NEW CONTACT MATERIALS BASED ONCOPPER AND ALUMINA
... The intensification in research of nanostructure materials in recent years has occurred primarily due to their attractive potential, i.e . mechanical and phy- sical properties significantly improved ...
4
Influence of Ion Implantation on the Structural and Stressed State and Mechanical Properties of Nitrides of High-entropy (TiZrAlYNb)N and (TiZrHfVNbTa)N Alloys
... Influence of Ion Implantation on the Structural and Stressed State and Mechanical Properties of Nitrides of High-entropy (TiZrAlYNb)N and (TiZrHfVNbTa)N Alloys.. O.V.[r] ...
6
Influence of Temperature on Mechanical Properties, Fracture Morphology and Strain Hardening Behavior of a 304 Stainless Steel
... the mechanical properties as a function of temperature were evaluated through the variations in the stress-strain curve and the strain hardening behavior was described in terms of strain hardening ...
11
Temperature-Dependent Mechanical Behaviors of Skin Tissue
... of temperature and the corresponding thermal denaturation of skin collagen on skin mechanical ...transition temperature of collagen in our skin samples is about ...increasing temperature due ...
10
Effect of Austenitizing Temperature on Mechanical Properties of the Mixed Bainite - Martensite Microstructure in CrMoV Steel
... austenite has no significant effect on the mechanical properties of various microstructures. Thus, the tensile and impact tests show that lower bainite is more ductile and tougher than martensite ...
8
Mat. Res. vol.20 número1
... Mechanical properties of graphenylene are studied here by employing molecular dynamics (MD) simulations. To this end, the efect of some parameters such as chirality and size on Young’s and bulk moduli of ...
9
Effect of Relative Humidities on Microstructural, Barrier and Mechanical Properties of Yam Starch-Monoglyceride Films
... present high capacity to interact with starch chains, enhancing the molecular mobility and increasing free volume in the film matrix, leading more weak and flexible films (Mali et ...
8
The Effect of Heat Treatment on Dynamic Strain Aging Behaviour of AISI H10 Hot Work Tool Steel
... In the present study, the workhardening rate (δy) of the AR and AQ samples were determined to examine whether DSA takes place or not, because generally an increased workhardening rate (δy) is a manifestation of DSA. The ...
10