• Nenhum resultado encontrado

Low carbon steel

The Effect of Temperature and Acid Concentration on Corrosion of Low Carbon Steel in Hydrochloric Acid Media

The Effect of Temperature and Acid Concentration on Corrosion of Low Carbon Steel in Hydrochloric Acid Media

... Abstract: Problem statement: The effect of different temperatures and acid concentrations on the corrosion of low carbon steel in hydrochloric acid were addressed in this study. Approach: The effect ...

7

Kinetics of austenite formation during continuous heating in a low carbon steel

Kinetics of austenite formation during continuous heating in a low carbon steel

... a low carbon steel, with initial microstructure composed of ferrite and pearlite, were studied during continuous heating, by using dilatometric analysis and measurements of microstructural ...

6

Formability Evaluation of Low-Carbon Steel Strip

Formability Evaluation of Low-Carbon Steel Strip

... Contribution concerns formability evaluation of low-carbon steel strip St 4, which is used for production of intricate deep stampings. The properties of sheet-metal which have the principal influence ...

10

Effects of Milling on Surface Integrity of Low-Carbon Steel

Effects of Milling on Surface Integrity of Low-Carbon Steel

... ISO P25) was employed for the endmill operation adopting a down-milling condition. A low-carbon alloy steel so-called commercially COS AR 60 with 10 x 24 x 100 mm was used for milling tests. The ...

7

Mat. Res.  vol.16 número2

Mat. Res. vol.16 número2

... interstitial-free steel sheet presented a very good formability level, which is suitable for exposed parts in which an extra deep-drawing quality is often ...a low carbon steel (AISI 1012) for ...

16

Formation mechanism of bimetal composite layer between LCS and HCCI

Formation mechanism of bimetal composite layer between LCS and HCCI

... resistant steel plates are widely used in the ields of metallurgy, cement, electricity, and mining under conditions of corrosive wear, impact abrasion and frictional ...resistant steel plate that consists ...

6

Investigation of Austenitic Stainless Steel Coatings on Mild Steel Produced by Friction Surfacing Using a Conventional CNC Machining Center

Investigation of Austenitic Stainless Steel Coatings on Mild Steel Produced by Friction Surfacing Using a Conventional CNC Machining Center

... stainless steel coatings on AISI 1020 low-carbon steel substrates using a machining center with Computerized Numerical Control (CNC) instead of dedicated friction surfacing equipment was ...

11

On the use of thermographic method to measure fatigue limits

On the use of thermographic method to measure fatigue limits

... Thermographic techniques originally proposed by Risitano proved to be really a much faster and easier way to obtain the fatigue limit of the tested low carbon steel. The utilization of a rotating ...

15

J. Braz. Chem. Soc.  vol.18 número1

J. Braz. Chem. Soc. vol.18 número1

... as low carbon steel, galvanized steel, aluminum and copper, which are commonly used in transmission and distribution power lines, were exposed to the environment in four of these 15 sites, in ...

14

J. Braz. Soc. Mech. Sci. & Eng.  vol.31 número1

J. Braz. Soc. Mech. Sci. & Eng. vol.31 número1

... The workpieces were truck side rails made with low-carbon steel (0.1% C, 0.24% Si, and 1.44% Mn) of 7 mm thick, and their initial Vickers hardness were about 2,300 ± 100 MPa. In punching, the first ...

5

NUMERICAL MODELING OF HEAT TRANSFER AND FLUID FLOW IN KEYHOLE PLASMA ARC WELDING OF DISSIMILAR STEEL JOINTS

NUMERICAL MODELING OF HEAT TRANSFER AND FLUID FLOW IN KEYHOLE PLASMA ARC WELDING OF DISSIMILAR STEEL JOINTS

... stainless steel and A36 low carbon steel using keyhole plasma arc welding has been simulated using a three dimensional numerical heat transfer and fluid flow ...stainless steel joint ...

13

J. Braz. Soc. Mech. Sci. & Eng.  vol.26 número1

J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1

... Thermally sprayed metallic coatings have been frequently applied over low carbon steel components, aiming at protecting against corrosion and wear. However, these coatings always contain pores, ...

9

J. Braz. Soc. Mech. Sci. & Eng.  vol.33 número2

J. Braz. Soc. Mech. Sci. & Eng. vol.33 número2

... of carbon on the kinetics of the process is made; effects of the activities of oxyfuel gases on the flame cutting process is also ...of carbon content and the cutting pressures on the cutting rates of ...

6

Jellyfish body plans provide allometric advantages beyond low carbon content.

Jellyfish body plans provide allometric advantages beyond low carbon content.

... and carbon contents but is critical when comparisons include animals, such as jellyfishes, that have vastly different carbon and water ...their carbon mass, rather than wet or dry mass is used to ...

10

Corrosion inhibition of carbon steel by extract of Buddleia perfoliata

Corrosion inhibition of carbon steel by extract of Buddleia perfoliata

... This behavior is not affected by the presence of the inhibitor, indicating the activation- controlled nature of the reaction; the semicircle diameter increases with the inhibitor concentration, reaching a maximum value ...

14

Effect of Quenching Media on Mechanical Properties for Medium Carbon Steel

Effect of Quenching Media on Mechanical Properties for Medium Carbon Steel

... medium carbon steel (one with copper and another without copper) have been studied and analyze result of mechanical testing performed on various heat treated samples for the two grades of ...of steel ...

9

Anti-Corrosive Effect of Tridax Procumbens – Zn2+ System  Controlling the Corrosion of Carbon Steel

Anti-Corrosive Effect of Tridax Procumbens – Zn2+ System Controlling the Corrosion of Carbon Steel

... Carbon steel (0.026%S, 0.06%P, 0.4%Mn, 0.1% C, and the rest Fe) specimen of dimension 1 cm x 4 cm x 0.2 cm were used for weight loss study. Carbon steel rod of the same composition, ...

7

Continuous Scanning Technique with Barkhausen Magnetic Noise for Carbon Steel Sheets

Continuous Scanning Technique with Barkhausen Magnetic Noise for Carbon Steel Sheets

... The aim of this work is to study and develop a surface scanning technique, based on Continuous Scanning Magnetic Barkhausen Noise (CSMBN), for the detection of non- homogeneous regions, related to sub and microstructural ...

12

Mat. Res.  vol.17 número5

Mat. Res. vol.17 número5

... Martensitic Carbon Steel particles in Super Duplex and Carbon Steel substrates has been ...blasted steel substrates and calculating the particle contamination using Rietveld ...

11

Corrosion Inhibition of Carbon Steel in Chloride and Sulfate Solutions

Corrosion Inhibition of Carbon Steel in Chloride and Sulfate Solutions

... Corrosion is a major problem in industry and in infrastructure; a huge sum of expenditure every year is spent on preventing, retarding, and repairing its damages. This work studies the engineering of an inhibitor for ...

6

Show all 9016 documents...

temas relacionados