• Nenhum resultado encontrado

[PDF] Top 20 Fabrication of 3D electrodes for biosensor applications

Has 10000 "Fabrication of 3D electrodes for biosensor applications" found on our website. Below are the top 20 most common "Fabrication of 3D electrodes for biosensor applications".

Fabrication of 3D electrodes for biosensor applications

Fabrication of 3D electrodes for biosensor applications

... motivation of this work was the early diagnosis of Alzheimer's disease, as it is one of the main forms of dementia that affects millions of people ...easy fabrication and low ... See full document

65

Design and fabrication by inkjet printing of electrodes for electromyography

Design and fabrication by inkjet printing of electrodes for electromyography

... healthcare applications are becoming an in- valuable tool for regular and non-intrusive monitor- ...kind of applications since they give information about the state of several vital organic ... See full document

102

Fabrication and Functionalization of In2O3 Thin Film Transistors for Biosensing Applications

Fabrication and Functionalization of In2O3 Thin Film Transistors for Biosensing Applications

... a biosensor is “a device which uses specific biochemical reactions mediated by isolated enzymes, immunosystems, tissues, organelles, or whole cells to detect chemical compounds, usually by use of ... See full document

65

Tomás Colaço Ribeiro Fernandes

Tomás Colaço Ribeiro Fernandes

... pioneering biosensor for detecting cancer biomarkers that combines electrochemical and optical recognition in the same analyzing spot, by taking advantage of laser direct writing to pattern transparent and ... See full document

62

A new amperometric glucose biosensor based on screen printed carbon electrodes with rhenium(IV) - oxide as a mediator

A new amperometric glucose biosensor based on screen printed carbon electrodes with rhenium(IV) - oxide as a mediator

... carbon electrodes (modified): 0.05 g of rhenium(IV)-oxide was added to 1 g carbon ink (Electrodag 421 SS, Acheson); the oxide-ink mixture was stirred for 10-30 minutes with a glass-rod or stainless steel ... See full document

12

Design And Construction Of 300W Audio Power Amplifier For Classroom

Design And Construction Of 300W Audio Power Amplifier For Classroom

... Microphone Preamplifier is to pre amplify the audio signals from the microphone or line (CD player, EVD player, etc...).Tone Preamplifier is to lift and cut the low frequency and high frequency of the signal. ... See full document

5

Model of knowledge representation about materials in the form of a relational database for CAPCAST system

Model of knowledge representation about materials in the form of a relational database for CAPCAST system

... specification of the prod- uct and it is the customer who has to decide whether he can or cannot accept the price dictated by the ...price of the product as dictated by the cost of ...procedure ... See full document

6

DESIGN AND FABRICATION OF TWINROTOR UAV

DESIGN AND FABRICATION OF TWINROTOR UAV

... version of the UAV is termed as a Micro Air Vehicle (MAV). A MAV is a class of unmanned aerial vehicles (UAV) that has a size restriction and may be ...observation of hazardous environments ... See full document

9

Amperometric biosensor for ascorbic acid

Amperometric biosensor for ascorbic acid

... concentration of ascorbic acid in foodstuffs, beverages and pharmaceuticals can be an index of quality, since it varies during production and storage stages [1, ...formation of collagen, assists the ... See full document

7

The Economics of Sub-optimal Policies for Traffic Congestion

The Economics of Sub-optimal Policies for Traffic Congestion

... work of Gallego, Montero, and Salas ...number of cars on the ...equilibrium of a game with a continuum of ...aspects of congestion ... See full document

27

Additive Fabrication of Anepectic Meshes

Additive Fabrication of Anepectic Meshes

... 1 of the Appendix), some being also tested to determine their Young’s Modulus (see Figure a - 2 of the ...6 of the Appendix) to establish their thermal ...set of results are listed in Table a ... See full document

53

Studies of corrosion behaviour in acid environment of binary Mg-Li alloys for plastic forming

Studies of corrosion behaviour in acid environment of binary Mg-Li alloys for plastic forming

... [1] A. Białobrzeski, K. Saja, K. Hubner: Ultralight Magnesium- Lithium Alloys VII International Scientific Conference PAN “Optimization of Production System in Foundries” Łódź, 11- 13 czerwiec 2007 r.; Archives ... See full document

4

Fabrication of polypyrrole/graphene oxide composite nanosheets and their applications for Cr(VI) removal in aqueous solution.

Fabrication of polypyrrole/graphene oxide composite nanosheets and their applications for Cr(VI) removal in aqueous solution.

... kinds of heavy metal ions, Cr(VI) ion is considered to be one of the most toxic ions, which is found to be ...result of discharging a mass of Cr(VI) ions from industrial waste and sewage, ... See full document

7

Enzymatic biosensor for the detection of dithiocarbamate fungicides: kinetic study of aldehyde dehydrogenase enzyme and biosensor optimization.

Enzymatic biosensor for the detection of dithiocarbamate fungicides: kinetic study of aldehyde dehydrogenase enzyme and biosensor optimization.

... Esquema analítico para estudo cinético da reação de hidrólise do substrato (propionaldeído), catalisada pela enzima aldeído desidrogenase.. Cubeta Volume ( µ L) Tempo (min) b.[r] ... See full document

9

Preparation of optically transparent electrodes.

Preparation of optically transparent electrodes.

... PREPARATION OF OPTICALLY TRANSPARENT ...preparation of transparent conducting glass electrodes by deposition of pure and fluorine doped SnO 2 films is ...probes of a volt-ohm ... See full document

5

Laser technology and 3D printing for production of biopolymer-based hollow microneedles patch for biomedical applications

Laser technology and 3D printing for production of biopolymer-based hollow microneedles patch for biomedical applications

... surface of PDMS using a pulsed infrared laser engraving machine ...size of 25µm in diameter and the laser speed can be adjustable up to ...form of RGB colour ...jet of nitrogen. Finally, a ... See full document

58

Design Fabrication And Partial-Analysis Of A 2-Wheeler Prototype That Runs On Compressed Air

Design Fabrication And Partial-Analysis Of A 2-Wheeler Prototype That Runs On Compressed Air

... The solenoid valve actuation and the pulse control is achieved using an optical crank position sensor circuit. The circuit mainly consists of vital components: optical emitter-receiver (OPB732), Astable ... See full document

5

Application of SWAT model for assessing effect on main functions of watershed ecosystem in Headwater, Thailand

Application of SWAT model for assessing effect on main functions of watershed ecosystem in Headwater, Thailand

... sustainability of agricultural systems and a threat to the integrity of aquatic ...reduction of soil fertility, loss of nutrients, and declines of crop yields in ...review of ... See full document

13

Mat. Res.  vol.8 número2

Mat. Res. vol.8 número2

... oxidation of the ...behavior of the composite electrodes, including pore and reinforcing particle shape, size and ...terms of electrode activity, due probably to the synergestic effects caused ... See full document

3

Development of a piezoelectric biosensor based on PVDF films

Development of a piezoelectric biosensor based on PVDF films

... achievement of the aims of the work. Specially in the case of non-porous PVDF, results indicated possible surface hydrophilicity improvements through coating or thin film deposit, although, this ... See full document

67

Show all 10000 documents...