[PDF] Top 20 Heat Transfer Augmentation for Electronic Cooling
Has 3592 "Heat Transfer Augmentation for Electronic Cooling" found on our website. Below are the top 20 most common "Heat Transfer Augmentation for Electronic Cooling".
Heat Transfer Augmentation for Electronic Cooling
... of electronic devices has been improving along with the rapid technology ...development. Cooling of electronic systems is consequently essential in controlling the component temperature and avoiding ... See full document
4
Performance of water and diluted ethylene glycol as coolants for electronic cooling
... and heat load to dissipate during operation ...the heat loads and heat fluxes the Conventional cooling technologies such as fan, heat sinks are unable to absorb and heat ... See full document
6
Experimental investigation on flow and heat transfer for cooling flush-mounted ribbons in a channel: Application of an EHD active enhancement method
... of electronic boards are constructed with small elements that generate considerable amount of ...heat. Cooling of these electronic boards constitutes an essential part for their reliable ... See full document
12
Inline Array Jet Impingement Cooling Using Al2O3 / Water Nanofluid In A Plate Finned Electronic Heat Sink
... nominal heat flux of ...the heat transfer coefficient, at the same time reduces the pressure drop across the ...on heat transfer and pressure loss using jet impingement and channel flow ... See full document
9
HEAT TRANSFER ENHANCEMENT OF SMALL SCALE HEAT SINKS USING VIBRATING PIN FIN
... electronics cooling together with different technologies to enhance the cooling ...fins heat sinks are extensively used to dissipate heat in electronics ...increase heat transfer ... See full document
9
A SOLUTION FOR A PHASE CHANGE TRANSIENT HEAT TRANSFER PROBLEM USING AN ELECTRONIC SPREADSHEET
... Numerical solution for a phase change transient heat transfer problem was found using an Excel™ spreadsheet. Besides, an enthalpy transforming model and the finite volume method were employed. At each time ... See full document
12
Experimental Investigation of Heat Transfer Effectiveness on Finned-Tube Thermoacoustic Heat Exchanger
... the heat transfer between two identical parallel-plate heat exchangers in an oscillating flow over a range of frequencies and gas displacement ...two heat exchanger plates was ...of ... See full document
6
Finite time exergoeconomic performance optimization of a thermoacoustic heat engine
... conventional heat engines, thermoacoustic engines (including prime mover and refrigerator) [1-4] have many advantages, such as simple structure, no or least moving parts, high reliability, working with ... See full document
14
Minimum energy requirement of an endoreversible desalination system of sea water
... of heat with finite conductance and an endoreversible heat engine whose working fluid undergo a cycle custom designed to match the utility ...a heat exchange network was calculated ...of ... See full document
16
FLATTENING EFFECT ON HEAT TRANSFER CHARACTERISTICS OF A SINTERED-WICK HEAT PIPE
... on heat transfer characteristics and the internal phenomena of a sintered-wick heat pipe has been investigated by using three-dimensional Finite Element ...of heat pipe were 6 mm and 200 mm, ... See full document
7
Rev. IBRACON Estrut. Mater. vol.10 número1
... Anderson et al [16] also proposes a mathematical model to de- scribe the several physical processes of an intumescent system considering mass and energy control. The process of expansion during intumescence is depicted ... See full document
12
Numerical Investigation of Single Phase Fluid Flow and Heat Transfer In Rectangular Micro Channel Using Nanofluids as A Cooling Liquid
... cartridge heaters as illustrated in fig.2(a).A schematic of micro channel heat sink with key dimension is shown in fig.2(b). The Fluid is flowing through a rectangular micro channel embedded in a test module. ... See full document
5
Thermal energy storage system using phase change materials: Constant heat source
... latent heat thermal energy storage (LHTES) systems integrated with solar heating systems was also ...the heat transfer rate is increased because of placing the metal ...latent heat storage ... See full document
8
Transient MHD Free Convective Flow of an Optically Thick Gray Gas Past a Moving Vertical Plate in the Presence of Thermal Radiation and Mass Diffusion
... of heat and mass transfer problems are of importance in many chemical formulations and reactive ...generations, cooling of nuclear reactors, the boundary layer control in aerodynamics and ... See full document
9
Thermal control ways for Li-Ion batteries cooling: A review / Caminhos de controle térmico para baterias de Li-Ion cooling: Uma avaliação
... of heat at the center of the battery ...the cooling air reached the cell ...air cooling system is capable to maintain the battery temperature within the desired ...air cooling strategies on ... See full document
15
Braz. J. Chem. Eng. vol.29 número2
... The performance of rotary dryers is dictated by three important transport phenomena, namely: solids transportation (Lisboa et al., 2007, Cao and Langrish, 1999; Renaud et al., 2000; Shahhosseini et al., 2000; Song et ... See full document
11
J. Braz. Soc. Mech. Sci. & Eng. vol.33 número especial 1
... the heat transfer due to reduction in channel size, as reported by some authors, the results exhibit discrepancies concerning the effect of heat flux, mass velocity and saturation temperature on the ... See full document
7
The focus ofthis research is to compare the flow and heat transfer to the cases where water
... Heat trmsfer results are presented for temperature, convective heat transfer coefRcient, heat flux, Prandtl number and Nusselt number (Nu) in tíie range of conditions studied as well as [r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... of heat flow promote the formation of temperature gradients in the liquid, which induce initial nucleation on the mold’s walls, with grain growth taking place toward the center of the cast ... See full document
8
Numerical computation of solar heat storage in phase change material/concrete wall
... during off peak period [5]. PCM can also be integrated into a building wall to acts like a heat reservoir to provide thermal comfort by reducing the cooling/heating loads. There is a significant increase in ... See full document
8
temas relacionados