[PDF] Top 20 J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
Has 10000 "J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3" found on our website. Below are the top 20 most common "J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3".
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... It is a great honour to announce that, in the last August, Thomson Scientific has confirmed that our JBSMSE (Journal of the Brazilian Society of Mechanical Sciences and Engineering) has been selected to be indexed in the ... See full document
1
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... Initially, surface roughness is positively affected by the wear progress to different extents depending on wear rate. On reaching a wear level above 0.2 mm, surface roughness tends to [r] ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... In this study, the Energy-Rate method will be utilized to detect the stability diagram of a forced parametric equation, and a function to be used as a gauge function for determining re[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... The general idea of this methodology is to simulate the implant process of a stent using the finite elements method, extract the sensitivities of its flexibility and stiffness and upda[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... Figure 5 represents the COHb variation in the venous blood for four different levels of physical activity. It was considered a typical subject, male, with 70 kg weight, 1.74 m height, and 30 years old at sea ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... The thermal boundary conditions were a uniform temperature at the channel inlet, equal to T in , and an adiabatic condition at the channel walls, except along any active heater, where[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... The machining performance of ultrasonic machining has been investigated by a few researchers using DOE techniques. Jadoun et al (2006) investigated the tool wear rate in ultrasonic drilling of engineering ceramics. The ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... The cutting forces are measured with calibrated strain gauge dynamometer. The tool wear is measured off-line at the end of each cut under 30 x enhanced. The temperature is sensed by the embedded thermocouple ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... The influence of the hygrothermal effects on the shear strength results was negligible (around 3% of decrease). The authors are indebted to Mr. Rogério Silva Almeida from EMBRAER for h[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... To eliminate those cost collisions, the cost of a given solution can be modified in order to reflect how close this solution is to having a non-placed small item fitted in the large ob[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... where w is the velocity, w / P w z is the pressure gradient, k is the thermal conductivity, W represents the viscous heating and W is J the equivalent stress. It is interesting to mention that studies using ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... A strategy for mesh adaption, using only mesh movement and nodal re-allocation, has the advantage that the mesh connectivity and number of elements and nodes do not vary with respect t[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número4
... The J-integral values were compared with the solutions obtained by Nikishkov and Atluri (1994) and with the ones for the initial mesh without adaptation (Araújo et ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... The maximum major true strain peaks were found to occur close to the die shoulder when using the cylindrical and shallow-ellipse punches (whose external congruence radius was smaller [r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número4
... As described previously, the composed cements contain other added constituents that should be mixed in the phase of clinker grinding. In this case, the grinded product should be inside a certain granulometry limit in ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... To evaluate accuracy and precision in the direct manufacturing process plates with shapes and dimensions (defined in section 2.1) were used (Fig. 2). The epoxy resin Vantico SL5260 supplied by Huntsman was used as ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número2
... The interfacial tension for each pair of liquids was measured by carefully placing a layer of the lighter liquid at the top of the surface of the heavier liquid, previously placed in a beaker, and then using a Lauda Ring ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... to 30 times the external diameter of the cross-section, the column is part of a braced frame and the fire is constrained to only one storey of the building, where the temperature is taken as uniform along the ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número2
... Mechanical property (hardness) and tribological properties (wear and coefficient of friction) were investigated to deduce the optimum manufacturing parameters and opt[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... We have shown with simple examples that the fractal dimension of a given primordial sequence may be unrelated to the fractal characteristics of the offspring sequence. This m[r] ... See full document
11
temas relacionados