[PDF] Top 20 J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
Has 10000 "J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1" found on our website. Below are the top 20 most common "J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1".
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... The maximum major true strain peaks were found to occur close to the die shoulder when using the cylindrical and shallow-ellipse punches (whose external congruence radius was smaller [r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... The purpose of the present paper is to study the effect of uniform suction or blowing directed normal to the wall on the steady laminar flow of an incompressible non-Newton[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... To evaluate accuracy and precision in the direct manufacturing process plates with shapes and dimensions (defined in section 2.1) were used (Fig. 2). The epoxy resin Vantico SL5260 supplied by Huntsman was used as ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... Geometrically nonlinear static and dynamic behaviour of laminate composite shells are analyzed in this work using the Finite Element Method (FEM).. Triangular elements with three nodes[r] ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... To analyze the influence of residual stresses on fatigue limit, several specimens of condition 2.3 (with the greatest roughness values) were submitted to a stress relief heat treatment. After that, these specimens were ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... Design objectives such as maximum bouncing acceleration of seat and sprung mass, root mean square (RMS) weighted acceleration of seat and sprung mass as per ISO2631 standards,[r] ... See full document
11
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... The Canadian Standard (1995), CEB (1991) specified limiting accelerations values for human comfort, without considering their associated natural vibration frequencies. Those values are expressed exclusively in terms of ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... Conventional cutting fluid application systems are relatively inefficient in the grinding process, particularly under conditions of severe application. The energy stored in fluids during their application is ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... upper 30 mm of the column, temperatures for sections 2 to 5 in the next segments, each with a 60 mm length, and the temperature in section 6 for the next segment, with 1730 mm length, shown in ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... In order to verify the applicability of the methodology under consideration, five axial hydraulic turbines were designed to evaluate the optimum minimum suction pressure coefficient va[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... By this way, the inertia matrix (symmetrical and with constant coefficients), the gyroscopic matrix (skew-symmetrical and a function of the rotating speed) and the complex stiffness m[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número1
... We have shown with simple examples that the fractal dimension of a given primordial sequence may be unrelated to the fractal characteristics of the offspring sequence. This m[r] ... See full document
11
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número4
... Factorial design, which has been widely used in other areas of arc welding technology, is inadequate for welding flux formulation because flux properties depend on t[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número2
... Because these experiments were carried out with a high depth of cut (4 mm), the heat generation during each revolution of the tool was also high. Therefore, the cutting edge [r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número4
... Sayed-Ahmed, M.E. and Attia, H.A., 2005, “The effect of Hall current on magneto hydrodynamic flow and heat transfer for Bingham fluids in a rectangular duct”, Canadian Journal of Physics, Vol. 83 No.6, pp. ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... Initially, surface roughness is positively affected by the wear progress to different extents depending on wear rate. On reaching a wear level above 0.2 mm, surface roughness tends to [r] ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número2
... Motta and Machado (1995) concluded that the cost of cutting fluids in machining is justified by the returns obtained in the form of savings through enhanced tool life and economic consumption of energy. Minke (1999) ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número4
... As described previously, the composed cements contain other added constituents that should be mixed in the phase of clinker grinding. In this case, the grinded product should be inside a certain granulometry limit in ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... The machining performance of ultrasonic machining has been investigated by a few researchers using DOE techniques. Jadoun et al (2006) investigated the tool wear rate in ultrasonic drilling of engineering ceramics. The ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número2
... Each sintering experiment was repeated three times aiming at to guarantee the results reproducibility. The samples were characterized by means of scanning electron microscopy and energy dispersive x-ray microprobe ... See full document
7
temas relacionados