[PDF] Top 20 Study of the Electromagnetic Properties of Textiles

Study of the Electromagnetic Properties of Textiles

... studies the influence of the human body on the antenna behaviour, obtaining gains equals ...in the ISM frequency bands 2.4 and 5.8 GHz, using the same materials described ...In ... See full document

177

Effect of water glass modification with nanoparticles of zinc oxide on selected physical and chemical properties of binder and mechanical properties of sand mixture

... this study, an attempt was made to carry out the modification of water glass with zinc ...nanoxide. The aim of the research was to determine what effect the modifier added ... See full document

4

Statistical properties of ionospheric stimulated electromagnetic emissions

... (7), the time-averaged power spectrum can be calculated for the data as it is shown in ...1. The pump and some of the SEE features (Leyser, 2001), such as the broad upshifted ... See full document

9

Mat. Res. vol.17 suppl.1

... coating of composites with absorbing paints yields materials that can absorb microwave radiation and still have approximately the same specific mass of the original ...composites. The ... See full document

6

Study In Some Quality Attribute Of Meat

... respectively. The present results were lower than the values reported by Kafe, (2001) in camel meat as ...Whereas, the present results disagreed with the result of Arguello ...that ... See full document

3

Influence of tungsten and titanium on the structure of chromium cast iron

... evaluate the tribological properties of materials used for parts of machinery and equipment constituting the friction ...determine the wear resistance and friction coefficient ... See full document

4

Effect of Multipoint Sequential Water Mist Cooling of Casting Die on Microstructure and Mechanical Properties of AlSi11 Alloy

... continuation of research on the use of water mist cooling in order to increase efficiency of the die-casting process for aluminum ...alloys. The paper describes the ... See full document

6

Statistical Assessment of the Effect of Chemical Composition on Mechanical Properties of Hypereutectic AlSi17CuNiMg Silumin

... casting of high- duty parts for automotive applications. A wide range of these alloys has been specified by Western ...was the aim of the authors of this study to “enrich” ... See full document

4

Effect of heat treatment parameters on the properties of low-alloy cast steel with microadditions of vanadium

... P1 0,26 1,22 0,38 0,02 0,02 0,96 0,15 0,19 0,07 0,016 0,03 P2 0,27 1,23 0,45 0,03 0,02 1,19 0,11 0,22 0,09 0,014 0,055 P4 0,21 1,13 0,39 0,03 0,02 0,91 0,11 0,18 0,09 0,015 0,035 To determine heat treatment effect on ... See full document

4

Analytical Determining Of The Steinmetz Equivalent Diagram Elements Of Single-Phase Transformer

... methodology of the Steinmetz Equivalent Diagram Elements applied to the prediction of Eddy current loss in a single-phase ...on the electrical circuit theory, the active and ... See full document

8

Distributions of grain parameters on the surface of aircraft engine turbine blades

... In the quality assurance system for components cast using the lost wax method, the object of evaluation is the grain size on the surface of the ...evaluating ... See full document

6

Modeling of Two-Stage Solidification: Part II Computational Verification of the Model

... In the work we assume that the first stage of solidification is the same for both modified and unmodified ...Thus, the same dendritic nucleation density is used in both ...affect ... See full document

6

CONTINUOUS CREATION IN THE PROBABILISTIC WORLD OF THE THEOLOGY OF CHANCE

... in the positive: Yes, He can, because He is the most perfect being and His omnipotence is absolutely ...underlying the answer to the last question is that the risk is not so great, or ... See full document

16

The comparison of the structure and microhardness of the tool steel C90 and HS 6-5-2 remelted with the electric arc

... examination of the structure and microhardness of surface layer of C90 non-alloy steel and HS 6-5-2 high speed steel after electric arc treatment are presented in the ...paper. ... See full document

4

Influence of vibrations during crystallization on mechanical properties and porosity of AlSi13Cu2 alloy

... number of defective products, so called defects shall approach to ...technology of production, introduces improvements which would help in accomplishment of this ...introduction of different ... See full document

4

Application of time-series analysis for prediction of molding sand properties in production cycle

... nature of manufacturing processes and permits prediction of future values of the process parameters or production results on the basis of the past data, recorded in ... See full document

5

The Influence Of CSR Awareness On Consumer Purchase Decision Of A Telecommunication Network In Ghana A Case Of La Nkwantanag Madina Municipality

... products of socially responsible firms, but are not willing to spend time on figuring out which firm is socially ...At the same time, a segment of consumers continue to buy products from firms with ... See full document

9

Plastic properties of cold-deformed ironbased sintered materials

... forming of sintered metal powders has limited practical application because of, among others, the deformation degree and initial porosity of ...drop of plastic properties ... See full document

4

The Existence Of Leading Islands Securing And The Border Areas Unitary State Of Indonesia An Analysis In Law Perspective

... support the management of coastal areas, so it can be arranged on the setting, management, utilization, preservation and protection and security of marine areas and determination of ... See full document

4

Investigating The Use Of Mobile Computing In Zimbabwe Polytechnics Case Of A Polytechnic In Zimbabwe

... and the Mobile fra mework‖ defined mobile computing as ―the use of computing devices, which usually interact in some way with a centralised information system while away from the normal fixed ... See full document

5