Preface DATA A4

Please note that specifications are subject to change without notice due to ongoing product improvements. Details of foundation work, duct work, insulation work, electrical wiring, power source switch and other items should be referred to the installation instructions. Details of foundation work, duct work, insulation work, electrical wiring, power source switch and other items should be referred to the installation instructions.

SPECIFICATIONS DATA A4

PEFY Model

EXTERNAL DIMENSIONS DATA A4

50 mm or less clearance between the top of the indoor unit and the end of the suspension bolt will make maintenance of the indoor heat exchanger easier. Access door of 450mmx450mm in the ceiling under the drain pan should be designed for cleaning and maintenance of the heat exchanger. Keep access space between ceiling and unit in case of bottom access.

PEFY-P20,25,32VMR-E-L/R

4. If using the intake duct, remove the air filter (supplied with the unit), then install the filter (locally supplied) on the suction side. If you are using a field-supplied air filter, attach it in a location where the filter can be easily serviced. If you are using a field-supplied air filter, attach it in a location where the filter can be easily serviced.

PEFY-P200, 250VMH-E

Keep the bottom maintenance service area clear when cleaning the heat exchanger. 2. Keep the service space for maintenance from the bottom when cleaning the heat exchanger. 3. Keep the service space at the bottom clear for maintenance when the fan motor is replaced.

PEFY-P200,P250VMHS-E

CENTER OF GRAVITY DATA A4

PEFY-P20, 25, 32VMR-E-L/R

ELECTRICAL WIRING DIAGRAMS DATA A4

Thermistor (pipe temp. detection/liquid) Thermistor (pipe temp. detection/gas) 1.5F Switch(for mode selection) Switch(for capacity code) Switch (10th digit address set) Switch (connection no. set) Switch(for mode selection) Switch ( for model selection) Switch (for voltage selection). LEV Float switch Connector (remote indication) Connector (central control) Connector (remote switch) Connector (damper) Transmission terminal thermistor (intake air temp. detection). ONOFF switch (for model selection) Switch (for static pressure selection) Switch (for static pressure selection) Plug (emergency operation) Thermistor (pipe temp. detection/liquid) Thermistor (pipe temp. detection/gas).

PEFY-P200,250VMH-E

SOUND LEVELS DATA A4

5-1. Sound levels

5-2. NC curves

PEFY-P200VMHS-E External Static Pressure: 50Pa

PEFY-P200VMHS-E

PEFY-P250VMHS-E External Static Pressure: 50Pa

PEFY-P250VMHS-E

FAN CHARACTERISTICS CURVES DATA A4

OPTIONAL PARTS DATA A4

7-1. Optional parts line up for the Indoor unit

PEFY-P-VMS1 (L) -E

PEFY-P-VMH (S) -E

The actual dust condition affects the life of the filter, which must be taken into account at the application site.

7-3. Drain pump

PEFY7-4. Control box replace kit

1 - 46INDOOR UNITS

Steering mechanism Direct drive from the engine Direct drive from the engine Direct drive from the engine Direct drive from the engine Steering mechanism Direct drive from the engine° Direct drive from the engine Direct drive from the engine Direct drive from the engine. Air filter pipe Coolant gas pipe Paste connection (liquid) Coolant pipe Brazing connection (gas). OD

PEFY-P20VMA2-E

100 860(Duct) 20

Bottom of indoor unit Maintenance access area (view from the direction of arrow A) Fig.1 Electrical box Access door 3. Access door Bottom of indoor unit Maintenance access area (view from the direction of arrow B). If the inlet duct is used, remove the air filter (supplied with the unit) and then install the filter (field supply) on the suction side.

Refrigerant piping Brazing connection (Liquid) Refrigerant piping Brazing connection (Gas) Terminal block (Power source) Terminal block (Transmission) Drain pipe (O.D.ø32). Drain pipe (I.D.ø32) Access door Ceiling surface For service maintenance, correctly install the access door in the intended place. SW5 (I.B.) Connector (emergency operation)Switch (to select static pressure)Switch (to select static pressure)Switch (BRANCH No.)Switch (set address 10th digit)Switch (set address 1s digit)Switch (to select mode )Switch (for model selection) LED (remote control power)LED (power).

Switch (for mode selection)Switch (for capacity code)Switch (for mode selection)Thermistor (pipe temperature detection/gas)Thermistor (pipe temperature detection/liquid)Connector (Wireless) Float switchConnector (Remote indication)Connector (Central control) Thermistor (intake air temperature detection) Connector. PEFY-VMA(L), VMA2 TO OUTDOOR UNIT BC CONTROLLER REMOTE CONTROL TO MA REMOTE CONTROL OFF ON (Blue) (Green) (Red). S (SHIELD) ACL connector (0-10V analog input)Connector (IT terminal) Connector (emergency control)Switch (for static pressure selection)Switch (for static pressure selection)Switch (BRANCH No.)Switch (address set of 10 digits) Switch (1s digit address set)Switch (for mode selection)Switch (for model selection) Switch (for mode selection)Switch (for capacity code)Switch (for mode selection)Thermistor (pipe temperature sensing/gas)Thermistor (pipe temperature sensing/liquid).

Connector (Remote indicator) Connector (Central control) Connector (Remote switch) Connector (Damper) Thermistor (inlet air temperature) SW2 (I.B.) SW3 (I.B.).

PEFY-P-VMA(L)-E, VMA2-E

PEFY-P-VMA(L)-E

PEFY-P20,25VMA(L)-E External Static Pressure: 35Pa

PEFY-P32VMA(L)-E External Static Pressure: 35Pa

PEFY-P71, 80VMA(L)-E External Static Pressure: 35Pa

7-2. Filter box

1 - 88INDOOR UNITS

PEFY-P- VMH-E-F

See "Fan Characteristic Curves" vs. External Static Pressure in the DATA BOOK for applicable airflow range. Sound pressure level (low-medium-high)/(low-high) (measured in anechoic space) Insulation material Air filter Protective device Refrigerant control device Connectable outdoor unit Dia. External wiring Refrigerant cycle Document Accessories Optional long-life filter Optional filter box Drain pump.

When the PEFY-P-VMH-E-F is connected to the outdoor unit, the maximum connectable total capacity of the indoor unit is as follows. Only the thermo sensor in the remote control or an additional external thermo sensor can be selected as the room temperature sensor. Because PEFY-P-VMH-E-F directly cools the outside air, condensation formation at the air outlet grilles is possible and should be taken into account.

Air filter should be installed in the air intake side and should be easy to maintain. Refrigerant pipe flare joint(gas M copper tube) Refrigerant pipe flare joint(liquid N copper tube) Drain hose I.D. 2. Keep the service space for maintenance from below when cleaning the heat exchanger.

PEFY-P80,140,200,250VMH-E-F

PEFY-P80, 140VMH-E-F

The drain pump runs continuously if the connector is inserted and the power supply is applied.).

PEFY-P200, 250VMH-E-F

CAPACITY TABLES DATA A4

7-1. Cooling capacity

7-3. Heating capacity

PEFY-P-VMH-E-F

8-3. Drain pump

PMFY-P-VBM-E

PMFY-P20, 25, 32, 40VBM-E

Center of gravity

P25VBM

P32VBM

P40VBM

B INDOOR CONTROLLER BOARD CN25

B CIRCUIT BOARD SW1

PMFY-P20VBM-E

PMFY-P25, 32VBM-E External static pressure : 0Pa

PMFY-P40VBM-E

TEMPERATURE/AIRFLOW DISTRIBUTIONS DATA A4

6-1. Temperature distributions

PMFY-P20-40VBM-E

6-2. Airflow distributions

PMFY-P20-40VBM-EC

1 - 116INDOOR UNITS

PLFY-P-VLMD-E

PLFY-P125VLMD-E

TRANSMISSION CONNECTION BED ) TO MA REMOTE CONTROL TO OUTDOOR UNIT Refrigerant distributor ME REMOTE CONTROL TB2. Connector (Central control) Connector (Remote indication)Connector (Central control)Connector (HA terminal-A) Auxiliary relay (L notch:240V). Fan motor Capacitor (for MF) Indoor controller board Power source connection bed Transmission connection bed MA Remote control connection bed Fuse (6.3 A/6 A) Transformer Drain pump Electronic linear expansion valve Drain sensor Vane motor Thermistor (inlet temperature sensing) Thermistor (pipe temperature sensing/liquid) Thermistor (pipe temperature sensing/gas) Switch (1s digit address set) Switch (10 digit address set) Switch (connection number set) Switch (for mode selection 1) Switch (for model selection )Switch (for capacity code) Switch (for mode selection 2) Auxiliary relay (M/L notch: 240V/220-230V) Auxiliary relay (H/M-notch:240V/220-230V)Auxiliary relay (H-notch:220-230V) Switch (for mode selection 3)Switch (for voltage selection).

Electronic linear expansion valve Internal control board Address board Power source terminal bed Transmission terminal bed Transmission terminal bed Fuse AC250V 6.3A F Transformer Drain pump Motor for vane (with limit switch) Drain sensor Thermistor (inlet temp. detection) Switch (1s digit address set ). NAME Thermistor (pipe temp.detection / liquid) Thermistor (pipe temp.detection / gas) Switch (10th digit address set) Switch (connection No.set) Switch (for mode selection) Switch (for capacity code) Switch (optional parts) Switch (for mode selection) SW4(I.B) Switch (for model selection).

PLFY-P40VLMD-E

PLFY-P80VLMD-E

OA INTAKE-STATIC PRESSURE CURVES DATA A4

Please confirm that the inlet air temperature (which is mixed with outside air) is in the following operating temperature range.

BRANCH DUCT INTAKE-STATIC PRESSURE CURVES DATA A4

8-1. Temperature distributions

PLFY-P20-125VLMD-E

8-2. Airflow distributions

9-2. OA duct flange

1 - 132INDOOR UNITS

Detailed drawing of fresh air intake Ceiling surface *The fresh air intake hole flange must be delivered in the field.

PLFY-P15, 20, 25, 32, 40VCM-E2

In case of wireless remote control: PLP-6BALM In case of standard grill: PLP-6BA.

Connected the attached

B INDOOR CONTROLLER BOARD CN32

B OPTION PART

B PCB FOR WIRELESS REMOTE CONTROLLER

B GRILLE

M LEV

2.In case of using MA-Remote controller, please connect to TB15. (The remote control wire is non-polar.) 3.In case of using M-NET, please connect to TB5. 4.The symbol [S] of TB5 is the shield wire connection. 5. The symbols used in the above connection diagram are, : terminal block, : connector.

PLFY-P20VCM-E2

PLFY-P25VCM-E2

PLFY-P32VCM-E2

PLFY-P40VCM-E2

PLFY-P15VCM-E2

PLFY-P15-40VCM-E2

PLFY-P-VBM-E

PLFY-P32-80VBM-E

PLFY-P100, 125VBM-E

7-2. Air outlet shutter plate

7-3. High efficiency filter element

7-6. Automatic filter elevation panel

7-7. Wireless signal receiver

7-8. Space panel

7-9. Duct flange for fresh air intake

1 - 152INDOOR UNITS

PCFY-P-VKM-E

High efficiency filter PAC-SH88KF-E PAC-SH89KF-E PAC-SH90KF-E PAC-SH90KF-E. Maintenance panel with air intake. Wireless Remote Control Kit PAR-SL94B-E PAR-SL94B-E PAR-SL94B-E PAR-SL94B-E. Remarks * Details on foundation work,. duct work, insulation work, wiring, power source switch and other items shall be referred to the installation manual.

PCFY-P40VKM-E

PCFY-P63VKM-E

PCFY-P100,125VKM-E

PCFY-P40,63,100,125VKM-E

PCFY-P40, 63, 100, 125VKM-E

NOTES

At servicing for outdoor unit, always follow the wiring diagram of outdoor unit

In case of using MA-Remote controller, please connect to TB15

LEGEND]

PCFY-P40VKM

PCFY-P63VKM

PCFY-P100VKM

PCFY-P125VKM

PCFY-P100, 125VKM-E

PCFY-P40, 63VKM-E

7-2. Airflow distributions Airflow distributions

8-2. High efficiency filter

8-4. Wireless remote controller kit

Drive mechanism Directly driven by motor Directly driven by motor Directly driven by motor Direct drive. Optional parts Outer box LEV PAC-SG95LE-E PAC-SG95LE-E PAC-SG95LE-E PAC-SG95LE-E. Notes * Details of foundation parts, duct parts, insulation parts, electrical wiring, power source switch and other items are in the installation manual. Notes * Details of foundation parts, duct parts, insulation parts, electrical wiring, power source switch and other items are in the installation manual.

Title plate First page Second page Transmission (DC 24-30V) MA remote control (DC8.7-13V) There is no MA remote control terminal block. In the case of connecting an MA remote control, connect the cable of the MA remote control (accessory) to the connector. Power supply (220-240V). Required space (indoor unit) Min.50 Min.220Min.150550mm or more with additional installation of drain pump.

Terminal block for power supply Terminal block for transmission Terminal block for MA remote control Emergency control switch (cooling / heating) Under sideVane (auto) Operating lamp 612. DEFROST / STABD BY lamp Operating lamp. lower pipingC. 108 mm or more with left or rear left pipe or drain mechanism installation Min.

550 mm or larger with optional installation of a drain mechanism. 265 mm or larger with optional installation of a drain mechanism.

PKFY-P100VKM-EPKFY-P25VBM-E

PKFY-P63VKM-E

PKFY-P15VBM-E 815 225 225

PKFY-P40VHM-E PKFY-P50VHM-E

PKFY-P15, 20, 25VBM-E

Please set the switch SW5 according to the power supply voltage

Legend Symbol

PKFY-P32, 40, 50VHM-E

B INDOOR CONTROLLER BOARD

B PCB FOR WIRELESS REMOTE CONTROLLERSW1

At servicing for outdoor unit,always follow the wiring diagram of outdoor unit
In case of using M-NET, please connect to TB5
Symbol [S] of TB5 is the shield wire connection
Symbols used in wiring diagram above are, : terminal

PKFY-P63, 100VKM-E

BPULL

PKFY-P15VBM-E

PKFY-P20, 25VBM-E External Static Pressure: 0Pa

PKFY-P32VHM-E

PKFY-P40VHM-E

PKFY-P50VHM-E

PKFY-P100VKM-E External Static Pressure: 0Pa

In the actual installation, they may vary from these figures under the influence of air temperature conditions, ceiling height, cooling/heating load, obstructions, etc.

7-2. External LEV Box

PFFY-P20, 25, 32, 40VKM-E2

Remote controller (PAR-F27MEA) can be built-in. Program timer cannot be built in together).

MODELS P20VBM

At servicing for outdoor unit,always follow the wiring diagram of outdoor unit

The setting of the SW2 dip switches differs in the capacity. For the detail, refer to the table below

Please set the switch SW5 according to the power supply voltage

SYMBOL I. B

POWER SUPPLY (I.B) POWER SUPPLY (I.B)

FAN MOTOR (UPPER) FAN MOTOR (LOWER)

SYMBOL

OPTION SELECTORNAME

ADDRESS BOARD

MARK

FUNCTION LED1

LED2

MMS3~

TO NEXT INDOOR UNIT Switch (connection number set) Switch (address set to 10 digits) Thermistor (pipe temperature/gas detection) Thermistor (pipe temperature/liquid detection) Switch (for mode selection). Switch (1s digit address set) Thermistor (inlet temperature sensing) Address board Indoor controller board Capacitor (for MF) Fan motor NAME SYMBOL Electronic linear expansion. Switch (for mode selection) Switch (for model selection) Switch (10th digit address set) Switch (connection number set) Switch (for static pressure selection) Switch (for static pressure selection) Thermistor (pipe temperature detection/gas) Thermistor (pipe temperature/liquid detection ) Transmission terminal bedTB15TB2 TB5 Transmission terminal bed Power source terminal bed L1 AC reactor (power factor improvement).