Juki MO-2400, MO-2500 Series Gauge Set Manual.pdf

This manual shows the dimensions of door plates, presser feet and feeders used on typical models, so you can select part gauges to suit your specific applications. For door panels, controllers, etc. their required dimensions are given so that you can select gauge parts to suit your specific applications. Note that the front views of the presser foot assembly show the toe guards, while the top views remove these toe guards.

The code represents a machine equipped with a presser foot to produce seams with better touch and appea. Note that this model of machine has a presser foot lift of 6 mm or less due to the larger hook of the stitch tongue. The particular machine code specifies a requirement other than replacement of the subclass gauge sets.

Use this list to find the model that best suits your application from a wide selection of sewing machines. You can imitate the safety stitches of medium weight materials by removing one of the two needles.

3C0 For Doeskin

Only MO-2500 series

For winding tape 2-needle double chainstitching For winding and sewing tape (neat finish on top and bottom) to pocket bags, etc. The gauges of 1-needle overlock machines, 2-needle overlook machines and safety stitch machines are grouped for easy reference be identified.

MO-2543E-BBD6-340

MO-2543E-DBD6-340

MO-2543E-FBD6-340

BBD6

DBD6

FBD6

MO-2443 Special

MO-2443E-BBD6-300 MO-2443E-BBD6-340

MO-2443E-FB06-300 MO-2443E-FBD6-340

MO-2445 Special

MO-2500/2400 Standard subclass machine specifications list

Closing stitch on the toes of tights, and turn-up seams of extremely light materials in scarves, etc. Turn-up seams of sock-toes, handkerchiefs, trousers, crepe de chine, silk, rayon, nylon, etc. Safety stitching of fabrics such as in men's shirts, and knitted materials such as jersey.

Lightweight fabric safety stitching of common fabrics and rugettes with larger needle gauge and opposite width.

Special usage subclass machine specification list

List of subclass machines classified by stitch type

For proper use of the asm. thread tension spring, see the "asm. tension controller" column. Description Travel needle guard Thread tension spring asm., (red) Thread tension spring asm., (yellow) Teruion thread spring asm., (blue). Description Travel needle guard Thread tension spring asm., (red) Thread tension spring asm., (yellow) Thread tension spring asm., (I>lue).

Description Bearing needle guard Wire lens spring asm., (yellow Wire tension spring asm., (yclIowl Wire tension spring asm., (yellow) Wire tempron spring asm., (blue). Other common parts Description Tmvolinn needle guard Wire tension spring asm. ., (red) Wire tension spring asm. yeilDw) Wire tension spring esm. b)uc). Wire tension spring asm., (red) Third tension spring asm., (red) Wire tension spring asm., (blue) Wire tension spring asm., (yellow).

Traveling needle guard Double chain looper Thread tension spring asm., (red) Thread tension spring asm., (yellow) Threatl tension spring ar— , (yellowj Thread tension spring^(blue). Description Traveling needle guard Ooubio-cKoin toopcf Thread tension spring asm., (rod) Screw tension spring asri., (red ) Screw tension spring asm., (b(uo) Thread tertsion spring asm., (yellow). Traveling needle guard Threod tension spring asm., (red Thread tension spring asm., (ycllowl Thread tension spring asm., (blue) Thread tertsion spring asm. , (yellow).

Description Travel needle guard Ooublcxhain looper Thread tension spring asm., (red) Thread tension spring asm., (yellow) Thread tension spring asm., (yellow) Thread tension spring < (blue). Other common part Description Trawl needle guard Oouble-chidn lusor Thread tension spring asm., (red) Thread tension spring asm. Other common pins Description Traveling needle guard Wire tension spring asm., (red) Wire tansiDn spring asm., (blue).

Other common parts Description Travel needle guard Thread tension spring asm, (red) Thread tension spring asm., (yellow) Thread tension spring asm., (blue) Lenston thread spring asm , (yellow). Description Travel needle guard Thread tension spring asm., (red) Thread tension spring asm., (yellow) Thread tension spring asm., (blue). Other common parts Description Travel needle guard Thread tension spring asm., (red) Thread tension spring asm., yellow) Thread tension spirrrg asm., (blue).

CHJ'

The standard gauge parts means gauge parts used for standard

The column "Applicable model" shows the model names of subclass machines for which the gauge parts are used
The column "Simultaneous replacement parts" shows parts that must be replaced at the same time when that part is
For throat plates, main feed dogs, differential feed dogs, and auxiliary feed dogs see Standard Subclass Gauge Parts List

For throat plates, main feed dogs, differential feed dogs and auxiliary feed dogs, see Standard Subclass Gauge Parts List.

81507804ROC

For 2-needle overlock machine for general fabrics, knitwear, jersey and the like (when look and feel are particularly important). For 2-needle overlock machine for imitation safety stitches on medium weight knits, jersey and similar. For 2-needle overlook machine for imitation safety stitches on medium weight knits, jersey, bulky fabrics, etc.

11875507 Application Simultaneous replacement parts

Gathering foot for safety stitches on light materials in general fabrics, knitwear, georgette, etc. Application Gathering foot for safety stitches (in wider needle size) on general fabrics, men's shirts, georgette,.

34;BTZEB

For sharp curved safety stitches (in wider needle size) of light general fabrics, men's shirts, knitwear, etc.

MO-2A43E-DBD6-340

MO-2A43E-FBD6-340

MO-2A43E-BBD6-300 MO-2A43E-BBD6-340

BBD6-300 BBD6-340

Replacement throat plate E01

Replacement feed dog (main feed dog, differential feed dog, and aux iliary feed dog) FOI-^

Replacement presser foot (presser foot assembly, presser foot, and stitch tongue or rear presser foot) G01~

R4508H0DDQB

MO-2A04E-0E4-300/E-04 (1-needle overlock machine)

11883204 Differential feed

STANDARD MO-2500/2400 REPLACEMENT THROAT PLATE LIST

11892205 Regulator hook

11892403 Screw

11892304 Regulator hook

J 1,11 III'

IVIO-2500/2400 REPLACEMENT FEED DOG LIST

AAAI

G-02 11879269 Presser foot asm

B1509804C0B Stitch tongue

B1507814B0B Tape attaching presser foot

B1507814B0E Tape attaching presser foot

11872108 Presser foot hinge

11875309 Rear presser

11873304 Hinging presser foot

81530816000 Front presser foot

11872702 Hinge arm for double

81530816F00 Front presser foot

11878766 Presser foot asm

B1507804C0A Presser foot

B1509804C00 Stitch tongue

B1509814B00 Stitch tongue

B1507816D0R Hinging presser foot

11875804 Reap presser

11880663 Presser foot asm

B150781400P Presser foot

B1507816D0C Hinging presser foot

81538816000 Stitch tongue

This list provides specifications, applications, adjustments, threading, etc. for each of the most popular models among those classified on the basis of the U.S. Also spare parts and exclusive voltage regulator asm. necessary to change the default subclass machines for each seam type are included. Needle height (the needle should be 10mm above the top surface of the neck plate when at the highest point of the stroke.).

UIF-

Thestandard radius andreturning amount of the double-chian looper ara63.2mm and1.8to 2mm, respectively

Position the needle thread take-up and needle thread take-up guides as shown below.). Position the needle thread guide to the far left for cotton thread and to the far right for synthetic thread. Height of needles (The needle must be 10 mm above the upper surface of the throat plate when they are at the highest point of their stroke.).

Adjust the upper and lower loops as shown below when they are on the far left side of their stroke.). The standard radius and return length of a double chain loop are 63.2 mm and 1.8 to 2 mm, respectively. Safety stitches of plain fabrics, knits such as jersey and medium weight materials Also used for 2- or 1-needle hemming of plain fabrics and knits by removing the double chain stitch needle.

Needle Height (Adjust the height of the needles to meet the requirements shown below when they are at the highest point of their stroke.). The height of the needle bar will refer to the overflow needle and be adjusted tolOmm. The standard radius and amount of double-chain ring resume are 63.2 mm and 1.B to 2 mm, respectively.

For winding tape reinforcement stitching (clean top and bottom finishing on pocket bag tops, etc.). The needle should be 10 mm above the top surface of the neck plate when they are at the highest point of their stroke.). How to Adjust the Double Chain Loop (Adjust the double chain loop as shown below when they are on the far left side of their stroke.).

JUKI

TBMYB JHKI INDUSTRIAL CS.. LTD