ULTRASCHALL-ENTFERNUNGS-
MESSER / ULTRASONIC DISTANCE
METER / TÉLÉMÈTRE À ULTRASONS
ULTRASCHALL-ENTFERNUNGSMESSER
Bedienungs- und Sicherheitshinweise
ULTRASONIC DISTANCE METER
Operation and Safety Notes
TÉLÉMÈTRE À ULTRASONS
Instructions d‘utilisation et consignes de sécurité
ULTRASONE AFSTANDMETER
Bedienings- en veiligheidsinstructies
MEDIDOR POR ULTRASONIDOS
Instrucciones de utilización y de seguridad
MEDIDOR DE DISTÂNCIAS POR ULTRA-SONS
Instruções de utilização e de segurança
ULTRAZVUKOVÝ MĚŘIČ VZDÁLENOSTÍ
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 5 GB / IE Operation and Safety Notes Page 22 FR / BE Instructions d‘utilisation et
consignes de sécurité Page 39 NL / BE Bedienings- en veiligheidsinstructies Pagina 56 CZ Pokyny pro obsluhu a
bezpečnostní pokyny Strana 73 ES Instrucciones de utilización y
de seguridad Página 89 PT Instruções de utilização e
7 8 9 10 11 3 5 4 12 14 13 1 6 2
A
Min. 0.6m
Max. 16m
B
7Einleitung
...Seite 6 Bestimmungsgemäße Verwendung ...Seite 6 Teilebeschreibung ...Seite 6 Technische Daten ...Seite 7 Lieferumfang ...Seite 7Allgemeine
Sicherheitshinweise
...Seite 7 Sicherheitshinweise für Batterien /Akkus...Seite 9
Vor der Inbetriebnahme
...Seite 10 Batterie einlegen / wechseln ...Seite 10Inbetriebnahme
...Seite 11 Länge messen ...Seite 11 Messfehler vermeiden ...Seite 12 Längen addieren ...Seite 13 Fläche messen ...Seite 14 Volumen messen...Seite 15 Flächen bzw. Volumina addieren ...Seite 16 Die letzten Messwerte anzeigen ...Seite 17 Temperaturanzeige ...Seite 17 Maßeinheit wechseln ...Seite 17 Batterieanzeige ...Seite 18 Ausschalten / AutomatischesAbschalten ...Seite 18
Fehlerbehebung
...Seite 18Reinigung und Pflege
...Seite 18Entsorgung
...Seite 19Ultraschall-Entfernungsmesser
Einleitung
Wir beglückwünschen Sie zum Kauf Ihres neuen Produkts. Sie haben sich damit für ein hochwertiges Produkt entschieden. Die Bedienungsanleitung ist Teil dieses Produkts. Sie enthält wichtige Hinweise für Sicherheit, Gebrauch und Entsorgung. Machen Sie sich vor der Benutzung des Produkts mit allen Bedien- und Sicherheitshinweisen vertraut. Benutzen Sie das Produkt nur wie beschrieben und für die angegebenen Einsatzbereiche. Händigen Sie alle Unterlagen bei Weitergabe des Produkts an Dritte mit aus.
Bestimmungsgemäße
Verwendung
Dieses Produkt ist zur Messung von Längen sowie zur Berechnung von Flächen und Volumina vorge-sehen. Zusätzlich verfügt das Produkt über eine Temperaturmessung. Das Produkt ist ausschließlich zur privaten Verwendung vorgesehen.
Teilebeschreibung
1 Ultraschallsender / –empfänger 2 Temperatursensor 3 FT/M-Taste 4 READ-Taste 5 RECALL-Taste 6 Referenzfläche 7 Libelle8 MODE-Taste
9 ON / OFF-Taste (EIN / AUS) 10 Display 11 Laserdiode 12 RESET-Taste 13 Batteriefachdeckel 14 Batteriefach
Technische Daten
Betriebsspannung: max. 9 V (Gleichstrom) Batterietyp: 6LR61 (9 V Blockbatterie) Messbereich: 0,6 m–16 m Messgenauigkeit: +/- 1%Anzeige Kapazität: bis 9999,99
Wellenlänge Laser: 635–660 nm, 1 mW Laser-Klasse: 2 Ultraschall-Frequenz: 40 kHz Messbereich Thermometer: –10 °C–+40 °C (14 °F–104 °F)
Lieferumfang
1 Ultraschall-Entfernungsmesser 1 9 V-Blockbatterie 1 BedienungsanleitungAllgemeine
Sicherheitshinweise
Machen Sie sich vor der ersten Benutzung des Produkts mit allen Bedien- und Sicherheitshinweisen
vertraut! Händigen Sie alle Unterlagen bei Wei-tergabe des Produkts an Dritte ebenfalls mit aus!
Kontrollieren Sie das Produkt vor der Inbe-triebnahme auf Beschädigungen! Nehmen Sie ein beschädigtes Produkt nicht in Betrieb! Setzen Sie das Produkt keiner Feuchtigkeit
aus! Es kann hierdurch beschädigt werden. Dieses Produkt kann von Kindern ab 8 Jahren
und darüber sowie von Personen mit verringer-ten physischen, sensorischen oder mentalen Fähigkeiten oder Mangel an Erfahrung und Wissen benutzt werden, wenn sie beaufsichtigt oder bezüglich des sicheren Gebrauchs des Produkts unterwiesen wurden und die daraus resultierenden Gefahren verstehen. Kinder dürfen nicht mit dem Produkt spielen. Reini-gung und Benutzerwartung dürfen nicht von Kindern ohne Beaufsichtigung durchgeführt werden.
Gefahr durch Laserstrahlung
LASERSTRAHLUNG NICHT IN DEN STRAHL BLICKEN
LASER KLASSE 2
635–660 nm
Das Produkt enthält einen Klasse-2-Laser. Rich-ten Sie den Laserstrahl niemals auf Personen oder Tiere. Blicken Sie nie direkt in den Strahl. Bereits ein schwacher Laserstrahl kann zu Au-genschäden führen.
Richten Sie den Laserstrahl niemals auf reflek-tierende Flächen oder Materialien. Auch ein reflektierter Laserstrahl kann Augenschäden hervorrufen.
Sicherheitshinweise für
Batterien / Akkus
LEBENSGEFAHR! Halten Sie Batterien /
Akkus außer Reichweite von Kindern. Suchen Sie im Falle eines Verschluckens sofort einen Arzt auf!
EXPLOSIONSGEFAHR! Laden
Sie nicht aufladbare Batterien nie-mals wieder auf. Schließen Sie Batterien / Akkus nicht kurz und / oder öffnen Sie diese nicht. Überhitzung, Brandgefahr oder Platzen können die Folge sein.
Werfen Sie Batterien / Akkus niemals in Feuer
oder Wasser.
Setzen Sie Batterien / Akkus keiner
mecha-nischen Belastung aus.
Risiko des Auslaufens von Batterien / Akkus
Vermeiden Sie extreme Bedingungen und Temperaturen, die auf Batterien / Akkus ein-wirken können, z. B. auf Heizkörpern / direkte Sonneneinstrahlung.
Vermeiden Sie den Kontakt mit Haut, Augen und Schleimhäuten! Spülen Sie bei Kontakt mit Batteriesäure die betroffenen Stellen sofort mit klarem Wasser und suchen Sie umgehend einen Arzt auf!
SCHUTZHANDSCHUHE TRAGEN! Ausgelaufene oder
be-schädigte Batterien / Akkus können bei Berührung mit der Haut Verätzungen ver-ursachen. Tragen Sie deshalb in diesem Fall geeignete Schutzhandschuhe.
Im Falle eines Auslaufens der Batterien / Akkus entfernen Sie diese sofort aus dem Produkt, um Beschädigungen zu vermeiden.
Verwenden Sie nur Batterien / Akkus des gleichen Typs. Mischen Sie nicht alte Batte-rien / Akkus mit neuen!
Entfernen Sie die Batterien / Akkus, wenn das Produkt längere Zeit nicht verwendet wird.
Risiko der Beschädigung des Produkts
Verwenden Sie ausschließlich den angege-benen Batterietyp / Akkutyp!
Setzen Sie Batterien / Akkus gemäß der Polaritätskennzeichnung (+) und (-) an Batterie / Akku und des Produkts ein. Reinigen Sie Kontakte an Batterie / Akku und
im Batteriefach vor dem Einlegen mit einem weichen Tuch!
Entfernen Sie erschöpfte Batterien / Akkus umgehend aus dem Produkt.
Vor der Inbetriebnahme
Entfernen Sie vor der Inbetriebnahme die Schutzfolie vom Display 10 des Produkts und legen Sie die beiliegende Batterie ein.
Batterie einlegen / wechseln
Wenn im Display 10 das Batteriesymbol erscheint, ist die eingelegte Batterie nahezu er-schöpft und muss ausgetauscht werden. Leere Batterien können das Messergebnis verfälschen.
Gehen Sie zum Einlegen der Batterie wie folgt vor:
Öffnen Sie den Batteriefachdeckel 13 auf der Rückseite des Produkts. Mit Hilfe des Stoffstrei-fens, der sich im Inneren des Batteriefachs 14 befindet, können Sie die alte Batterie leichter herausnehmen. Ziehen Sie hierzu lediglich am Stoffstreifen.
Entfernen Sie die Batterieklemme von der Batterie.
Stecken Sie die Kontakte der 9 V-Blockbatterie auf die Batterieklemme. Achten Sie hierbei auf die richtige Polarität. Diese ist durch die Profilform der Kontakte vorgegeben. Achten Sie unbedingt auch darauf, dass der Stoff-streifen sich unterhalb der Batterie befindet.
Legen Sie die Batterie in das Batteriefach und schließen Sie den Deckel wieder, so dass er hörbar einrastet.
Inbetriebnahme
Länge messen
Drücken Sie die ON / OFF-Taste 9, um das Produkt einzuschalten. Drücken Sie 60 s lang keine Taste, schaltet sich das Display 10 ab.
Um das Produkt manuell auszuschalten, hal-ten Sie die ON / OFF-Taste 3 Sekunden lang gedrückt, bis das Display erlischt und ein doppeltes Tonsignal ertönt.
Drücken Sie die MODE-Taste 8 so oft, bis das Display das Symbol für Längenmessung „ “ sowie die Längenangabe 0.00 m (bzw. 0‘00‘‘) zeigt.
Halten Sie die Referenzfläche 6 des Produkts an den Anfangspunkt Ihrer Messung. Halten Sie das Produkt so, dass die Referenzfläche parallel zur Zielfläche der Messung ausge-richtet ist.
Verwenden Sie zur waagerechten Ausrichtung des Produkts ggf. die Libelle 7. Die Luftblase der Libelle befindet sich bei waagerechter Aus-richtung zwischen den beiden Markierungen
.
Drücken Sie die READ-Taste 4. Die Laserdi-ode 11 projiziert einen Leuchtpunkt auf die Fläche des Endpunkts der Messung. Dieser Leuchtpunkt hilft Ihnen, das Produkt korrekt auszurichten. Nach erfolgreicher Messung wird die gemessene Länge im Display angezeigt.
Messfehler vermeiden
Um Messfehler zu vermeiden, beachten Sie die folgenden Hinweise:
Die Messung erfolgt mit Ultraschall, der sich kegelförmig vom Ultraschallsender 1 fortbe-wegt. Von der Zielfläche wird der Schall zu-rückgeworfen und vom Ultraschallempfänger empfangen. Aus der Laufzeit des Signals be-rechnet das Produkt die zu messende Länge (Abb. B).
Um eine genaue Messung zu gewähr-leisten, sind folgende Bedingungen einzuhalten (Abb. B):
Die Referenzfläche (A) muss parallel zur Zielfläche (B) sein.
Die zu messende Strecke muss zwischen 0,6 m und 16 m lang sein.
Im Schallkegel dürfen sich keine Gegenstände befinden, die den Schall verfrüht reflektieren. Der Schallkegel hat bei einer Länge von 16 m eine Breite von etwa 6 m.
Die Zielfläche muss eine glatte Oberfläche haben, damit der Schall gut reflektiert werden kann.
Durchsichtige Flächen wie Glas reflektieren in der Regel den Schall.
Die Batterie darf nicht leer sein. Eine leere Batterie wird im Display 10 durch das Batte-riesymbol angezeigt.
Wenn eine eindeutige Messung nicht möglich ist, zeigt das Display die Angabe „Err“. Die Messung muss dann wiederholt werden.
Wenn das Display einfriert oder das Produkt nicht richtig funktioniert, öffnen Sie den Batte-riefachdeckel und entnehmen Sie die Batterie aus dem Batteriefach. Drücken Sie dann die RESET-Taste mit einem spitzen Gegenstand. Das Display wird neu gestartet und nimmt wieder den normalen Betrieb auf.
Hinweis: Entehmen Sie die Batterie nicht,
während Sie die RESET-Taste drücken.
Längen addieren
Messen Sie eine Länge wie im Kapitel „Länge messen“ beschrieben. Der Betrag der Länge erscheint in der oberen Zeile des Displays 10.
Drücken Sie nun die RECALL-Taste 5. Der Betrag der Länge wird auf die untere Zeile übertragen. Das bedeutet, dass er im Sum-menspeicher abgelegt worden ist. Oben im Display erscheint das Zeichen „+“.
Das Produkt zeigt so an, dass es für eine neue Längenmessung bereit ist.
Drücken Sie die READ-Taste 4. Der Betrag der nun gemessenen Länge erscheint oben im Display.
Drücken Sie die RECALL-Taste. Der Messwert wird dann in den Summenspeicher übernom-men und unten erscheint die Summe der bei-den gemessenen Längen. Sollte die Messung eine Fehlmessung sein, drücken Sie nicht die RECALL-Taste, sondern erneut die READ-Taste. Der oben angezeigte Messwert wird über-schrieben. Drücken Sie die RECALL-Taste, um den Wert in den Summenspeicher zu über-nehmen.
Sie können diesen Vorgang beliebig oft wie-derholen, solange die Länge von 9999,99 m nicht überschritten wird.
Fläche messen
Hinweis: Um methodische Messfehler zu
ver-meiden, machen Sie sich bitte zunächst mit den Hinweisen zur Messung von Längen vertraut.
Drücken Sie die ON / OFF-Taste 9, um das Produkt einzuschalten.
Drücken Sie die MODE-Taste 8 so oft, bis im Display 10 das Symbol für Flächenmes-sung „ “sowie die Anzeige 0.00 m (bzw. 0‘00‘‘) erscheint. Das Symbol „ “ für Län-genmessung blinkt. Das Produkt zeigt so an, dass es für die erste Messung bereit ist.
Richten Sie das Produkt aus und drücken Sie die READ-Taste 4. Bei erfolgreicher Messung wird oben im Display die gemessene Länge
angezeigt. Außerdem blinkt das Symbol für Breitenmessung „ “. Das Produkt zeigt so an, dass es für die Messung der Breite bereit ist.
Richten Sie das Produkt aus und drücken Sie erneut die READ-Taste. Bei erfolgreicher Mes-sung erscheint oben im Display die gemessene Breite und unten die Fläche in der Maßeinheit m2 (bzw. sq.ft = Quadratfuß).
Für eine erneute Flächenmessung drücken Sie kurz die MODE-Taste. Die Anzeigen im Display werden zurückgesetzt und das Produkt ist be-reit für eine neue Fächenmessung.
Volumen messen
Hinweis: Um methodische Messfehler zu
ver-meiden, machen Sie sich bitte zunächst mit den Hinweisen zur Messung von Längen vertraut.
Drücken Sie die ON / OFF-Taste 9, um das Produkt einzuschalten.
Drücken Sie die MODE-Taste 8 so oft, bis im Display 10 das Symbol „ “ für Volumen-messung sowie die Anzeige 0.00 m (bzw. 0‘00‘‘) erscheint. Das Symbol „ “ für Län-genmessung blinkt. Das Produkt zeigt so an, dass es für die erste Messung bereit ist.
Richten Sie das Produkt aus und drücken Sie die READ-Taste 4. Bei erfolgreicher Messung wird oben im Display die gemessene Länge angezeigt. Außerdem blinkt das Symbol für Breitenmessung „ “. Das Produkt zeigt so an, dass es zur Messung der Breite bereit ist.
Richten Sie das Produkt aus und drücken Sie die READ-Taste. Bei erfolgreicher Messung wird oben im Display die gemessene Breite angezeigt. Außerdem blinkt das Symbol für
Höhenmessung „ “. Das Produkt zeigt so an, dass es zur Messung der Höhe bereit ist.
Richten Sie das Produkt aus und drücken Sie erneut die READ-Taste. Bei erfolgreicher Messung erscheint oben im Display die gemessene Höhe und unten das Volumen in der Maßeinheit m3 (bzw. cu.ft = Kubikfuß).
Für eine erneute Volumenmessung drücken Sie kurz die MODE-Taste. Die Anzeigen im Display werden zurückgesetzt und das Produkt ist bereit für eine neue Volumenmessung.
Flächen bzw. Volumina
addieren
Messen Sie eine Fläche bzw. ein Volumen wie im Kapitel „Fläche messen“ bzw. „Volumen messen“ beschrieben. Der Betrag der Fläche / des Volumens erscheint in der unteren Zeile des Displays.
Drücken Sie die RECALL-Taste 5, um das Messergebnis zu speichern. Im Display 10 erscheint das Symbol M+ und zeigt an, dass das unten im Display angezeigte Messergeb-nis im Produkt gespeichert ist.
Drücken Sie kurz die MODE-Taste 8. Das Produkt ist nun bereit zur Messung der nächs-ten Fläche / des nächsnächs-ten Volumens.
Messen Sie die nächste Fläche / das nächste Volumen so, wie Sie die erste Messung vor-genommen haben.
Drücken Sie nun erneut die RECALL-Taste, um auch das neue Ergebnis in den Summenspei-cher aufzunehmen. Das Ergebnis der Addition wird in der unteren Zeile des Displays ange-zeigt.
Wenn Sie weitere Flächen /Volumina hinzufü-gen möchten, wiederholen Sie die Schritte 3 bis 5.
Halten Sie die MODE-Taste 3 Sekunden ge-drückt, um den Additionsmodus zu verlassen.
Die letzten Messwerte
anzeigen
Drücken Sie nach der Messung einer Fläche oder eines Volumens wiederholt die READ-Taste 4, um die einzelnen Messwerte der Messung anzuzeigen.
Das Symbol des entsprechenden Messwertes blinkt und das Messergebnis wird in der oberen Zeile des Displays angezeigt.
Temperaturanzeige
Halten Sie die FT/M-Taste 3 für ca. 3 Sekun-den gedrückt. Im Display 10 wird die aktuelle Raumtemperatur in der amtlichen Temperatur-einheit °C angezeigt.
Um in die Temperatureinheit °F umzuschalten, drücken Sie kurz die FT/M-Taste.
Drücken Sie kurz die MODE-Taste 8, um den Temperaturanzeigemodus zu verlassen.
Maßeinheit wechseln
Drücken Sie die FT/M-Taste 3, um von der amtlichen Maßeinheit Meter auf die Maßein-heit Fuß (Anzeige Fuß‘ Zoll‘‘) umzuschalten.
Batterieanzeige
Bei niedrigem Batterieladezustand erscheint im Display 10 das Batteriesymbol . Tauschen Sie bei Erscheinen dieses Symbols schnellstmög-lich die Batterie aus. Leere Batterien können das Messergebnis verfälschen. Der Batteriewechsel wird im Kapitel „Batterie einlegen / wechseln“ beschrieben.
Ausschalten / Automatisches
Abschalten
Schalten Sie das Produkt aus, indem Sie die ON/OFF-Taste 9 3 Sekunden lang gedrückt halten.
Fehlerbehebung
Fehler Mögliche Ursache und Lösung
Das Produkt reagiert nicht. Elektrostatische Entladungen können zu Funktionsstörun-gen führen.
Öffnen Sie das Batterie-fach 13, Und drücken Sie die RESET-Taste 12 mit einem spitzen Ge-genstand.
Reinigung und Pflege
Reinigen Sie das Produkt nur äußerlich mit einem weichen trockenen Tuch.
Entsorgung
Die Verpackung besteht aus umwelt-freundlichen Materialien, die Sie über die örtlichen Recyclingstellen entsor-gen können. Der Grüne Punkt gilt nicht für Deutschland.
b a
Beachten Sie die Kennzeichnung der Verpackungsmaterialien bei der Abfall-trennung, diese sind gekennzeichnet mit Abkürzungen (a) und Nummern (b) mit folgender Bedeutung: 1–7: Kunststoffe / 20–22: Papier und Pappe / 80–98: Verbundstoffe. Das Produkt und die Verpackungsma-terialien sind recycelbar, entsorgen Sie diese getrennt für eine bessere Abfall-behandlung. Das Triman-Logo gilt nur für Frankreich.
Möglichkeiten zur Entsorgung des aus-gedienten Produkts erfahren Sie bei Ihrer Gemeinde- oder Stadtverwaltung. Werfen Sie Ihr Produkt, wenn es aus-gedient hat, im Interesse des Umwelt-schutzes nicht in den Hausmüll, sondern führen Sie es einer fachgerechten Ent-sorgung zu. Über Sammelstellen und deren Öffnungszeiten können Sie sich bei Ihrer zuständigen Verwaltung infor-mieren.
Defekte oder verbrauchte Batterien / Akkus müssen gemäß Richtlinie 2006/66/EG und deren Ände-rungen recycelt werden. Geben Sie Batterien / Akkus und / oder das Produkt über die angebotenen Sammeleinrichtungen zurück.
Umweltschäden durch falsche Entsorgung der Batterien / Akkus!
Batterien / Akkus dürfen nicht über den Hausmüll entsorgt werden. Sie können giftige Schwermetalle enthalten und unterliegen der Sondermüllbehand-lung. Die chemischen Symbole der Schwermetalle sind wie folgt: Cd = Cadmium, Hg = Quecksilber, Pb = Blei. Geben Sie deshalb verbrauchte Batterien / Akkus bei einer kommunalen Sammelstelle ab.
Garantie
Das Produkt wurde nach strengen Qualitätsrichtlinien sorgfältig produziert und vor Anlieferung gewissen-haft geprüft. Im Falle von Mängeln dieses Produkts stehen Ihnen gegen den Verkäufer des Produkts gesetzliche Rechte zu. Diese gesetzlichen Rechte werden durch unsere im Folgenden dargestellte Garantie nicht eingeschränkt.
Sie erhalten auf dieses Produkt 3 Jahre Garantie ab Kaufdatum. Die Garantiefrist beginnt mit dem Kaufdatum. Bitte bewahren Sie den Original-Kassen-bon gut auf. Diese Unterlage wird als Nachweis für den Kauf benötigt.
Tritt innerhalb von 3 Jahren ab dem Kaufdatum dieses Produkts ein Material- oder Fabrikations-fehler auf, wird das Produkt von uns – nach
unserer Wahl – für Sie kostenlos repariert oder ersetzt. Diese Garantie verfällt, wenn das Produkt beschädigt, nicht sachgemäß benutzt oder gewartet wurde.
Die Garantieleistung gilt für Material- oder Fabri-kationsfehler. Diese Garantie erstreckt sich nicht auf Produktteile, die normaler Abnutzung ausgesetzt sind (z. B. Batterien) und daher als Verschleißteile angesehen werden können, oder für Beschädi-gungen an zerbrechlichen Teilen, z. B. Schalter, Akkus oder die aus Glas gefertigt sind.
Introduction
...Page 23 Intended use ...Page 23 Parts description ...Page 23 Technical Data ...Page 24 Scope of delivery ...Page 24General safety
instructions
...Page 24 Safety instructions for batteries /rechargeable batteries...Page 26
Before using
...Page 27 Inserting / changing the battery ...Page 27Start-up
...Page 28 Measuring length ...Page 28 Avoiding measuring errors ...Page 29 Adding lengths together ...Page 30 Measuring surface area ...Page 31 Measuring volume ...Page 32 Adding surface areas or volumestogether ...Page 33 Displaying the last measured values ....Page 34 Temperature display ...Page 34 Changing the unit of measurement ...Page 34 Battery state display ...Page 35 Switching off / Automatic shut-down ....Page 35
Troubleshooting
...Page 35Cleaning and Care
...Page 35Disposal
...Page 36Ultrasonic Distance Meter
Introduction
We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information con-cerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the unit as described and for the specified ap-plications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.
Intended use
This product is intended for measuring lengths and for calculating surface areas and volumes. The product also has a temperature measuring facility. This product is solely intended for private use.
Parts description
1 Ultrasonic transmitter / receiver 2 Temperature sensor 3 FT/M button 4 READ button 5 RECALL button 6 Reference area 7 Level indicator 8 MODE button 9 ON / OFF button
10 Display 11 Laser diode 12 Reset Key
13 Battery compartment cover 14 Battery compartment
Technical Data
Operating voltage: max. 9 V
(Direct current)
Battery type: 6LR61 (9V Block
battery)
Measuring range: 0.6 m–16 m
Measuring accuracy: +/- 1%
Capacity display: up to 9999.99
Laser wave length: 635–660 nm, 1 mW
Laser class: 2 Ultrasonic frequency: 40 kHz Thermometer measuring range: -10 °C–+40 °C (14 °F– 104 °F)
Scope of delivery
1 Ultrasonic Distance Meter 1 9 V-blockbattery
1 Set of operating instructions
General safety
instructions
Before using the product, please familiarise yourself with all of the safety information and instructions
for use! When passing this product on to others, please also include all the documents!
Check the product for damage before use! Never use a damaged product!
Do not expose the product to moisture! This may damage it.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabili-ties or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Danger from laser radiation
LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
635–660 nm
The product contains a Class 2 laser. Never point the laser beam at persons or animals. Never look directly into the beam. Even a weak laser beam can cause eye damage. Never point the laser beam at reflective
sur-faces or materials. Even a reflected laser beam can cause eye damage.
Safety instructions for
batteries / rechargeable
batteries
DANGER TO LIFE! Keep batteries /
re-chargeable batteries out of reach of children. If accidentally swallowed seek immediate medical attention.
DANGER OF EXPLOSION!
Never recharge non-rechargeable batteries. Do not short-circuit bat-teries / rechargeable batbat-teries and / or open them. Overheating, fire or bursting can be the result.
Never throw batteries / rechargeable batter-ies into fire or water.
Do not exert mechanical loads to batteries / rechargeable batteries.
Risk of leakage of batteries / rechargea-ble batteries
Avoid extreme environmental conditions and temperatures, which could affect batteries / rechargeable batteries, e.g. radiators / direct sunlight.
Avoid contact with the skin, eyes and mucous membranes. In the event of contact with bat-tery acid, thoroughly flush the affected area with plenty of clean water and seek immedi-ate medical attention.
WEAR PROTECTIVE GLOVES!
Leaked or damaged batteries / rechargeable batteries can cause burns on contact with the skin. Wear suitable protective gloves at all times if such an event occurs.
In the event of a leakage of batteries / rechargeable batteries, immediately remove them from the product to prevent damage.
Only use the same type of batteries / rechargeable batteries. Do not mix used and new batteries / rechargeable batteries.
Remove batteries / rechargeable batteries if the product will not be used for a longer period.
Risk of damage of the product
Only use the specified type of battery / rechargeable battery!
Insert batteries / rechargeable batteries ac-cording to polarity marks (+) and (-) on the battery / rechargeable battery and the product.
Clean the contacts on the battery / recharge-able battery and in the battery compartment using a soft dry cloth before inserting!
Remove exhausted batteries / rechargeable batteries from the product immediately.
Before using
Before initial use, remove the protective film from the product display 10 and insert the enclosed battery.
Inserting / changing
the battery
If the battery symbol appears in the display 10, the inserted battery is almost drained and must be replaced. Empty batteries can falsify the measured result.
To insert the battery proceed as follows:
Open the battery compartment cover 13 on the back of the product. You can remove the used battery more easily with the aid of the material strip, which is inside the battery compartment 14. Just pull on the material strip.
Remove the battery clip from the battery
Plug the contacts of the 9 V-blockbattery on the contacts of the battery clip. Make sure you fit the batteries the right way round. This is specified by the profiled shape of the con-tacts. Also ensure without fail that the material strip is underneath the battery.
Insert the battery in the battery compartment and close the cover again, so that it audibly latches into place.
Start-up
Measuring length
Press the ON/OFF button 9 to switch the product on. If you do not press any button for 60 s, the display 10 shuts down.
To switch the product off manually, hold the ON/OFF button pressed down for 3 seconds, until the display goes out and a double tone signal sounds.
Press the MODE button 8 repeatedly, until the display shows the symbol for length meas-urement “ “ as well as the length designa-tion 0.00 m (or 0‘00“).
Hold the reference area 6 of the product at the start point of your measurement. Hold the product in such a way, that the reference
area is aligned parallel to the target area of the measurement.
If necessary use the level indicator 7 to align the product horizontally. The air bubble of the level indicator should be between the two markings if the alignment is hori-zontal.
Press the READ button 4. The laser diode 11 projects a dot of light onto the end point of the measurement. This dot of light will help you to correctly align the product. After successful measuring, the length will appear in the display.
Avoiding measuring errors
In order to avoid measuring errors, please note the following information:
The measurement is performed by ultrasound, which travels from the ultrasonic transmitter 1 in a conical manner. The ultrasound is reflected from the target area and received by the ul-trasonic receiver. The product calculates the measured length (Fig. B) from the travel time of the signal.
In order to guarantee an exact measure-ment, the following conditions must be maintained (Fig. B):
The reference area (A) must be parallel to the target area (B).
The distance to be measured must be between 0.6 m and 16 m long.
There must be no objects in the conical path of the ultrasound, which could reflect the ul-trasound prematurely. The conical path of the
ultrasound has a width of about 6 m at a length of 16 m.
The target area must have a smooth surface, so that the ultrasound can be well reflected.
Transparent surfaces, such as glass, generally reflect the ultrasound.
The battery must not be empty. An empty bat-tery is shown in the display 10 by the battery
symbol .
If a definitive measurement is not possible, the display shows the “Err“ information. The measurement must then be repeated.
If the display of the product hang-up or the product doesn‘t work well, open the battery cover, move the battery out of battery com-partment, press the RESET button using a sharp object. Then the product display will restart and resume to normal.
Note: Do not disconnect the battery while
using RESET button.
Adding lengths together
Measure a length as described in the section “Measuring length“. The length appears in the top line of the display 10.
Now press the RECALL button 5. The length is transferred to the bottom line. This means that it has been saved in the aggregate memory. The character “+“ appears at the top of the display. The product displays in this way, that it is ready for a new length measurement.
Press the READ button 4. The length, which has now been measured, appears at the top of the display.
Press the RECALL button. The measured value is then transferred to the aggregate memory, and the aggregate of the two measured lengths appears at the bottom of the display. If the measurement is an incorrect measure-ment, do not press the RECALL button but press the READ button again. The measured value, which is displayed at the top, is over-written. Press the RECALL button to adopt the value into the aggregate memory.
You can repeat this procedure as often as you wish, as long as the length of 9999.99 m is not exceeded.
Measuring surface area
Note: In order to avoid errors in the measuring
method, please familiarize yourself first with the information about measuring lengths.
Press the ON/OFF button 9 to switch the product on.
Press the MODE button 8 repeatedly until the symbol for surface area measurement “ “, as well as the designation 0.00 m (or 0‘00“), appear in the display 10. The symbol “ “ for length measurement flashes. The product displays in this way, that it is ready for the first measurement.
Align the product and press the READ button 4. If the measurement is successful, the length will appear at the top of the display. The symbol for width measurement “ “ also flashes. The product displays in this way, that it is ready for the measurement of the width.
Align the product and press the READ button again. If the measurement is successful, the width appears at the top of the display, and at the bottom appears the surface area in the m2 unit of measurement (or sq.ft = square feet).
Press the MODE button briefly, if a further surface area measurement is required. The figures in the display are reset, and the product is ready for a new surface area measurement.
Measuring volume
Note: In order to avoid errors in the measuring
method, please familiarize yourself first with the information about measuring lengths.
Press the ON / OFF button 9 to switch the product on.
Press the MODE button 8 repeatedly until the symbol “ “ for volume measurement, as well as the designation 0.00m (or 0‘00“), appear in the display 10. The symbol “ “ for length measurement flashes. The product displays in this way, that it is ready for the first measurement.
Align the product and press the READ button 4. If the measurement is successful, the length will appear at the top of the display. The sym-bol for width measurement “ “ also flashes. The product displays in this way, that it is ready for the measurement of the width.
Align the product and press the READ button. If the measurement is successful, the width will appear at the top of the display. The symbol for height measurement “ “ also flashes. The product displays in this way, that it is ready for the measurement of the height.
Align the product and press the READ button again. If the measurement is successful, the height appears at the top of the display, and at the bottom appears the volume in the m3
unit of measurement (or cu.ft = cubic feet).
Press the MODE button briefly, if a further volume measurement is required. The figures in the display are reset, and the product is ready for a new volume measurement.
Adding surface areas or
volumes together
Measure a surface area or volume as de-scribed in the section “Measuring surface area“ or “Measuring volume“. The surface area / volume appears in the bottom line of the display.
Press the RECALL button 5 to save the meas-ured result. The symbol M+ appears in the display and this indicates that the measured result, which is shown at the bottom of the display, is saved in the product 10.
Press the MODE button 8 briefly. The prod-uct is now ready to measure the next surface area or volume.
Measure the next surface area or volume in the same way as you performed the first measurement.
Now press the RECALL button again to adopt the new result into the aggregate memory. The result of the addition is shown in the bottom line of the display.
If you would like to add further surface areas or volumes, repeat steps 3 to 5.
Hold the MODE button pressed down for 3 seconds in order to leave the Addition mode.
Displaying the last
measured values
After you have measured a surface area or a volume, press the READ button 4 repeatedly in order to display the individual values of the measurement.
The symbol of the corresponding measured value flashes, and the measured result is shown in the top line of the display.
Temperature display
Hold the FT/M button 3 pressed down for approx. 3 seconds. The current room temper-ature, in the official °C temperature unit, is shown in the display 10.
In order to switch over to the °F temperature unit, press the FT/M button briefly.
Press the MODE button 8 briefly in order to leave the temperature display mode.
Changing the unit of
measurement
Press the FT/M button 3 in order to switch over from the official metric unit of measure-ment to the imperial unit of measuremeasure-ment (display in feet‘ and inches“).
Battery state display
If the battery charge status is low, the battery symbol appears in the display 10. Replace the battery as quickly as possible, if this symbol appears. Empty batteries can falsify the measured result. The battery change is described in the section “Inserting / changing the battery“.
Switching off /
Automatic shut-down
Switch the product off by holding the ON/ OFF button 9 pressed down for 3 seconds.
Troubleshooting
Error Possible causes and solutions
If the product does not react, electro-static discharge can affect the function of the product.
Open the battert com-partment 13, press the RESET button 12 with a pointed object.
Cleaning and Care
The product should only be cleaned on the outside with a soft dry cloth.
Disposal
The packaging is made entirely of re-cyclable materials, which you may dis-pose of at local recycling facilities. The Green Dot is not valid for Germany.
b a
Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1–7: plastics / 20–22: paper and fibre-board / 80–98: composite materials. The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.
Contact your local refuse disposal authority for more details of how to dispose of your worn-out product. To help protect the environment, please dispose of the product properly when it has reached the end of its use-ful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.
Faulty or used batteries / rechargeable batteries must be recycled in accordance with Directive 2006/66/EC and its amendments. Please return the batteries / rechargeable batteries and / or the product to the available collection points.
Environmental damage through incorrect disposal of the batteries / rechargeable batteries!
Batteries / rechargeable batteries may not be disposed of with the usual domestic waste. They may contain toxic heavy metals and are subject to hazardous waste treatment rules and regulations. The chemical symbols for heavy metals are as fol-lows: Cd = cadmium, Hg = mercury, Pb = lead. That is why you should dispose of used batteries / rechargeable batteries at a local collection point.
Warranty
The product has been manufactured to strict qua-lity guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.
The warranty for this product is 3 years from the date of purchase. Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you. The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe lo-cation. This document is required as your proof of purchase. This warranty becomes void if the pro-duct has been damaged, or used or maintained improperly.
The warranty applies to defects in material or ma-nufacture. This warranty does not cover product parts subject to normal wear, thus possibly consi-dered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts.
Introduction
...Page 40 Utilisation conforme ...Page 40 Descriptif des pièces ...Page 40 Caractéristiques techniques ...Page 41 Contenu de la livraison ...Page 41Instructions générales de
sécurité
...Page 41 Consignes de sécurité relativesaux piles / aux piles rechargeables ...Page 43
Avant la mise en service
...Page 44 Mise en place / remplacement dela pile ...Page 45
Mise en service
...Page 45 Mesurer des longueurs ...Page 45 Évitez les erreurs de mesure ...Page 46 Ajouter des longueurs ...Page 47 Mesurer des surfaces ...Page 48 Mesurer des volumes ...Page 49 Additionner des surfaces ou desvolumes ...Page 50 Afficher la dernière valeur de mesure ...Page 51 Affichage de la température ...Page 52 Modifier l‘unité de mesure...Page 52 Affichage de l‘usure de la batterie ...Page 52 Arrêt / Mise hors service automatique ...Page 52
Dépannage
...Page 53Nettoyage et entretien
...Page 53Mise au rebut
...Page 53Télémètre à ultrasons
Introduction
Nous vous félicitons pour l‘achat de votre nouveau produit. Vous avez opté pour un produit de grande qualité. Le mode d‘emploi fait partie intégrante de ce produit. Il contient des indications impor-tantes pour la sécurité, l’utilisation et la mise au rebut. Veuillez lire consciencieusement toutes les indications d‘utilisation et de sécurité du produit. Ce produit doit uniquement être utilisé conformé-ment aux instructions et dans les domaines d‘application spécifiés. Lors d‘une cession à tiers, veuillez également remettre tous les documents.
Utilisation conforme
Ce produit est conçu pour mesurer des longueurs et pour calculer des surfaces et des volumes. En outre, le produit dispose d‘un système de mesure de la température. Le produit est exclusivement conçu pour un usage privé.
Descriptif des pièces
1 Émetteur/récepteur d‘ultrasons 2 Capteur de température 3 Touche FT/M 4 Touche READ 5 Touche RECALL 6 Plan de référence 7 Niveau à bulles 8 Touche MODE
9 Touche ON/OFF (allumé/éteint) 10 Écran
11 Diode laser 12 Touche RESET
13 Couvercle du compartiment à piles 14 Compartiment à piles
Caractéristiques techniques
Tension de service : max. 9 V (courant continu)
Type de pile : 6LR61 (pile 9 V)
Plage de mesure : 0,6 m–16 m
Précision de mesure : +/- 1%
Capacité d‘affichage : jusqu‘à 9999,99 Longueur d‘ondes du laser : 635–660 nm, 1 mW
Catégorie du laser : 2
Fréquence des ultrasons : 40 kHz Plage de mesure du thermomètre : –10 °C – +40 °C (14 °F – 104 °F)
Contenu de la livraison
1 télémètre à ultrasons 1 pile 9 V 1 mode d‘emploiInstructions générales
de sécurité
Prenez connaissance de toutes les indications de maniement et de sécurité avant d‘utiliser l‘appa-reil pour la première fois ! Transmettez également
tous les documents en cas de transmission du produit à une personne tierce !
Avant la mise en service, vérifiez si le produit présente des dommages ! Ne mettez pas un appareil endommagé en service !
Tenez le produit à l‘abri de l‘humidité ! Il risque d’être endommagé.
Ce produit peut être utilisé par des enfants âgés de 8 ans et plus ainsi que par des per-sonnes ayant des capacités physiques, senso-rielles ou mentales réduites ou manquant d‘expérience ou de connaissances, s‘ils sont surveillés ou s‘ils ont été informés de l‘utilisation sûre du produit et s‘ils comprennent les risques liés à son utilisation. Les enfants ne doivent pas jouer avec le produit. Le nettoyage et l‘entre-tien du produit ne doivent pas être effectués par des enfants laissés sans surveillance.
Risque lié au rayon laser
RAYONNEMENT LASER NE PAS REGARDER DANS LE FAISCEAU
APPAREIL A LASER DE CLASSE2 635–660 nm
Le produit contient un laser de classe 2. N‘orien-tez jamais le laser sur des personnes ni des animaux. Ne regardez jamais directement dans le rayon. Un rayon laser de faible inten-sité peut suffire à provoquer des lésions ocu-laires.
N‘orientez jamais le laser sur des surfaces ou métaux réfléchissants. Le reflet du rayon laser peut également causer des lésions oculaires.
Consignes de sécurité
relatives aux piles / aux
piles rechargeables
DANGER DE MORT ! Rangez les piles /
piles rechargeables hors de la portée des enfants. En cas d’ingestion, consultez immédiatement un médecin !
RISQUE D‘EXPLOSION ! Ne
rechargez jamais des piles non rechargeables. Ne court-circuitez pas les piles / piles rechargeables et / ou ne les ouvrez pas ! Autrement, vous risquez de provoquer une surchauffe, un incendie ou une explosion.
Ne jetez jamais des piles / piles rechargeables au feu ou dans l’eau.
Ne pas soumettre les piles / piles
rechargea-bles à une charge mécanique.
Risque de fuite des piles / piles rechar-geables
Évitez d’exposer les piles / piles rechargeables à des conditions et températures extrêmes susceptibles de les endommager, par ex. sur des radiateurs / exposition directe aux rayons du soleil.
Évitez tout contact avec la peau, les yeux ou les muqueuses ! En cas de contact avec l’acide d’une pile, rincez la zone touchée à l’eau claire et consultez immédiatement un médecin !
PORTER DES GANTS DE PRO-TECTION ! Les piles / piles
re-chargeables endommagées ou sujettes à des fuites peuvent provoquer des brûlures au contact de la peau. Vous devez
donc porter des gants adéquats pour les manipuler.
En cas de fuite des piles / piles rechargeables, retirez-les aussitôt du produit pour éviter tout endommagement.
Utilisez uniquement des piles / piles rechar-geables du même type. Ne mélangez pas des piles / piles rechargeables usées et neuves !
Retirez les piles / piles rechargeables, si vous ne comptez pas utiliser le produit pendant une période prolongée.
Risque d‘endommagement du produit
Exclusivement utiliser le type de pile / pile rechargeable spécifié.
Insérez les piles / piles rechargeables confor-mément à l‘indication de polarité (+) et (-) in-diquée sur la pile / pile rechargeable et sur le produit.
Nettoyez les contacts de la pile / pile rechar-geable et du compartiment à pile avant d‘insérer la pile !
Retirez immédiatement les piles / piles rechar-geables usées du produit.
Avant la mise en service
Avant la mise en service, retirez le film de protection de l‘écran 10 du produit et insérez la pile fournie.
Mise en place /
remplacement de la pile
Si le symbole de la batterie s‘affiche à l‘écran 10, cela signifie que la pile est presque vide et qu‘elle doit être remplacée. Les piles vides risquent de fausser les résultats des mesures.
Pour le remplacement de la pile, veuil-lez procéder de la façon suivante :
Ouvrez le couvercle du compartiment à piles 13 situé au dos du produit. La bande en tissu à l’intérieur du compartiment à piles 14 vous permet de retirer plus facilement les piles usées. Pour ce faire, tirez légèrement sur la bande de tissu.
Enlevez les bornes des piles.
Placez les contacts de la pile 9 V sur les bornes. Vérifiez que la polarité est correcte. Celle-ci dépend de la forme des contacts. Veillez impérativement à ce que la bande de tissu se trouve en dessous de la pile.
Placez la pile dans le compartiment à piles et refermez le couvercle, jusqu’à ce qu’il s’en-clenche de façon audible.
Mise en service
Mesurer des longueurs
Appuyez sur la touche ON / OFF 9 pour allumer le produit. Si vous n‘appuyez sur aucune touche pendant 60 s, l‘écran 10 s‘éteint.
Pour éteindre le produit manuellement, main-tenez la touche ON / OFF enfoncée pendant
3 secondes, jusqu‘à ce que l‘écran s‘éteigne et qu‘un signal sonore retentisse deux fois.
Appuyez sur la touche MODE 8 jusqu‘à ce que le symbole de mesure des longueurs « » s‘affiche à l‘écran, ainsi que l‘indica-tion de longueur 0.00 m (ou 0‘00‘‘).
Maintenez le plan de référence 6 du produit au point de départ de votre mesure. Tenez le produit de façon à ce que le plan de référence soit orienté de façon parallèle à la surface cible de la mesure.
Le cas échéant, utilisez la nivelle 7 pour ali-gner le produit horizontalement. Si la surface est bien alignée à l‘horizontale, la bulle d‘air de la nivelle se trouve entre les deux
mar-quages .
Appuyez sur la touche READ 4. La diode la-ser 11 projet un point lumineux sur la surface du point final de la mesure. Ce point lumineux vous aide à orienter correctement le produit. Si la mesure est effectuée avec succès, la lon-gueur mesurée s‘affiche dans la partie supé-rieure de l‘écran.
Évitez les erreurs de mesure
Afin d‘éviter les erreurs de mesure, veuillez respecter les indications sui-vantes :
La mesure est effectuée par ultrasons, qui se déplacent de façon conique à partir de l‘émetteur d‘ultrasons 1. L‘onde sonore est répercutée par la surface cible et réception-née par le récepteur d‘ultrasons. À partir du temps de parcours du signal, le produit calcule la longueur à mesure (ill. B).
Afin de veiller à ce que les mesures soient précises, les conditions suivantes doivent être respectées (fig. B) :
Le plan de référence (A) doit être parallèle à la surface cible (B).
La distance à mesurer doit être comprise entre 0,6 m et 16 m de long.
Il ne doit pas y avoir d‘objet susceptible de réfléchir l‘onde sonore de façon prématurée dans la zone d‘émission des ultrasons. La zone d‘émission des ultrasons couvre une lon-gueur de 16 m et une largeur d‘environ 6 m.
La surface cible doit présenter une surface lisse, afin que l‘onde sonore puisse être ré-fléchie correctement.
Les surfaces transparentes comme le verre reflètent généralement l‘onde sonore.
La pile ne doit pas être vide. Le symbole de batterie affiché à l‘écran 10 indique que la pile est vide.
Si la mesure ne peut pas être effectuée de façon indiscutable, l‘écran affiche le message « Err ». La mesure est ensuite renouvelée.
Si l‘écran gèle ou si le produit ne fonctionne pas correctement, ouvrez le couvercle du compar-timent à piles et retirez la pile du comparcompar-timent. Ensuite, appuyez sur le bouton RESET avec un objet pointu. L‘écran redémarre et reprend son fonctionnement normal.
Remarque : Ne retirez pas la batterie tout
en appuyant sur le bouton RESET.
Ajouter des longueurs
Mesurez une longueur tel que décrit dans le chapitre « Mesurer des longueurs ». La valeur
de la longueur s‘affiche sur la ligne supérieure de l‘écran 10.
Appuyez alors sur la touche RECALL 5. La valeur de la longueur est déplacée sur la ligne inférieure. Cela signifie que la valeur a été enregistrée dans la mémoire du compteur. Le symbole « + » s‘affiche dans la partie su-périeure de l‘écran. Le produit indique ainsi qu‘il est prêt à effectuer une nouvelle mesure.
Appuyez sur la touche READ 4. La valeur de la longueur mesurée alors s‘affiche dans la partie supérieure de l‘écran.
Appuyez sur la touche RECALL. La valeur de mesure est ensuite reprise dans la mémoire du compteur et la somme des deux longueurs mesurées s‘affiche dans la partie inférieure. Si la mesure est erronée, n‘appuyez pas sur la touche RECALL, mais à nouveau sur la touche READ. La valeur de mesure affichée dans la partie supérieure est écrasée. Ap-puyez sur la touche RECALL, pour reprendre la valeur dans la mémoire du compteur.
Vous pouvez répéter cette opération tant que la longueur ne dépasse pas 9999,99 m.
Mesurer des surfaces
Remarque : afin d‘éviter les erreurs de mesure
méthodiques, veuillez d‘abord prendre connais-sance des indications concernant les mesures des longueurs.
Appuyez sur la touche ON / OFF 9 pour allumer le produit.
Appuyez sur la touche MODE 8 jusqu‘à ce que le symbole de mesure des surfaces
« » s‘affiche à l‘écran 10 et que l‘indication 0.00 m (ou 0‘00‘‘) apparaisse. Le symbole «
» de mesure des longueurs clignote. Le produit indique ainsi qu‘il est prêt pour la première mesure.
Alignez le produit et appuyez sur le bouton READ 4. Si la mesure est effectuée avec succès, la longueur mesurée s‘affiche dans la partie supérieure de l‘écran. En outre, le symbole de mesure des largeurs « » clignote. Le pro-duit indique ainsi qu‘il est prêt pour mesurer la largeur.
Alignez le produit et appuyez à nouveau sur le bouton READ. Si la mesure est effectuée avec succès, la largeur mesurée s‘affiche dans la partie supérieure de l‘écran et la surface est indiquée en m² (ou sq.ft. = mètres carré)
dans la partie inférieure.
Pour mesurer une nouvelle surface, appuyez brièvement sur la touche MODE. L‘affichage à l‘écran est réinitialisé et le produit est prêt pour mesurer une nouvelle surface.
Mesurer des volumes
Remarque : afin d‘éviter les erreurs de mesure
méthodiques, veuillez d‘abord prendre connais-sance des indications concernant les mesures des longueurs.
Appuyez sur la touche ON / OFF 9 pour allumer le produit.
Appuyez sur la touche MODE 8 jusqu‘à ce que le symbole « » pour la mesure des volumes s‘affiche à l‘écran 10 et que l‘indica-tion 0.00 m (ou 0‘00‘‘) apparaisse. Le symbole « » de mesure des longueurs clignote. Le
produit indique ainsi qu‘il est prêt pour la pre-mière mesure.
Alignez le produit et appuyez sur le bouton READ 4. Si la mesure est effectuée avec succès, la longueur mesurée s‘affiche dans la partie supérieure de l‘écran. En outre, le sym-bole de mesure des largeurs « » clignote. Le produit indique ainsi qu‘il est prêt pour mesurer la largeur.
Alignez le produit et appuyez sur le bouton READ. Si la mesure est effectuée avec succès, la largeur mesurée s‘affiche dans la partie su-périeure de l‘écran. En outre, le symbole de mesure des hauteurs « » clignote. Le pro-duit indique ainsi qu‘il est prêt pour mesurer la hauteur.
Alignez le produit et appuyez à nouveau sur le bouton READ. Si la mesure est effectuée avec succès, la hauteur mesurée s‘affiche dans la partie supérieure de l‘écran et le volume est indiqué en m3 (ou cu.ft = mètres cube)
dans la partie inférieure.
Pour mesurer un nouveau volume, appuyez brièvement sur la touche MODE. L‘affichage à l‘écran est réinitialisé et le produit est prêt pour mesurer un nouveau volume.
Additionner des surfaces
ou des volumes
Mesurez une surface ou un volume comme décrit dans le chapitre « Mesurer des surfaces » ou « Mesurer des volumes ». La valeur de la surface / du volume s‘affiche sur la ligne inférieure de l‘écran.
Appuyez sur la touche RECALL 5 pour enre-gistrer le résultat de la mesure. Le symbole M+ s‘affiche à l‘écran 10, ce qui signale que le résultat de mesure indiqué dans la partie inférieure de l‘écran est enregistré dans le produit.
Appuyez brièvement sur la touche MODE 8. Le produit est alors prêt à mesurer la surface suivante / le volume suivant.
Mesurez la surface suivante / le volume suivant, de la même façon que vous avez effectué la première mesure.
Appuyez ensuite à nouveau sur la touche RECALL, afin de reprendre le nouveau résultat dans la mémoire du compteur. Le résultat de l‘addition est affiché sur la ligne inférieure de l‘écran.
Si vous souhaitez ajouter d‘autres surfaces/ volumes, répétez les étapes 3 à 5.
Maintenez la touche MODE enfoncée pendant 3 secondes, pour quitter le mode Addition.
Afficher la dernière
valeur de mesure
Après avoir mesuré une surface ou un volume, appuyez à nouveau sur la touche READ 4 pour afficher les valeurs de mesure individuelles de la mesure.
Le symbole de la valeur de mesure corres-pondante clignote et le résultat de la mesure est affiché sur la ligne supérieure de l‘écran.
Affichage de la température
Maintenez la touche FT/M 3 enfoncée pendant env. 3 secondes. La température am-biante actuelle s‘affiche à l‘écran 10 en °C.
Pour passer l‘unité de température en °F, appuyez brièvement sur la touche FT/M.
Appuyez brièvement sur la touche MODE 8, pour quitter le mode Affichage de la tempé-rature.
Modifier l‘unité de mesure
Appuyez sur la touche FT/M 3, pour passer de l‘unité de mesure Mètre à l‘unité de mesure Pied (Affichage pied‘ pouce‘‘).
Affichage de l‘usure
de la batterie
Si la batterie est faible, le symbole de batterie s‘affiche à l‘écran 10. Si le symbole s‘affiche, remplacez les piles dès que possible. Les piles vides risquent de fausser les résultats des mesures. La procédure de changement des piles est décrite dans le chapitre « Mise en place/remplacement de la pile ».
Arrêt/Mise hors service
automatique
Éteignez le produit en appuyant sur la touche ON / OFF 9 pendant 3 secondes.
Dépannage
Dysfonctionne-ment Cause possible et solution Le produit ne réagit pas. Les décharges électrostatiques peuvent occasionner des dysfonctionne-ments. Ouvrez le compartiment à piles 13 et appuyez sur le bouton RESET 12 à l'aide d'un objet pointu.
Nettoyage et entretien
Nettoyez uniquement l’extérieur du produit à l’aide d’un chiffon doux et sec.
Mise au rebut
L’emballage se compose de matières recyclables pouvant être mises au rebut dans les déchetteries locales. Le «point vert» n‘est pas valable en Allemagne.
b a
Veuillez respecter l‘identification des matériaux d‘emballage pour le tri sé-lectif, ils sont identifiés avec des abbré-viations (a) et des chiffres (b) ayant la signification suivante : 1–7 : plastiques / 20–22 : papiers et cartons / 80–98 : matériaux composite.
Le produit et les matériaux d’emballage sont recyclables, mettez-les au rebut sé-parément pour un meilleur traitement des déchets. Le logo Triman n’est valable qu’en France.
Votre mairie ou votre municipalité vous renseigneront sur les possibilités de mise au rebut des produits usagés. Afin de contribuer à la protection de l’environnement, veuillez ne pas jeter votre produit usagé dans les ordures ménagères, mais éliminez-le de manière appropriée. Pour obtenir des rensei-gnements concernant les points de col-lecte et leurs horaires d’ouverture, vous pouvez contacter votre municipalité. Les piles / piles rechargeables défectueuses ou usagées doivent être recyclées conformément à la directive 2006/66/CE et ses modifications. Les piles et / ou piles rechargeables et / ou le pro-duit doivent être retournés dans les centres de collecte proposés.
Pollution de l’environnement par la mise au rebut incorrecte des piles / piles rechargeables !
Les piles / piles rechargeables ne doivent pas être mises au rebut avec les ordures ménagères. Elles peuvent contenir des métaux lourds toxiques et doivent être considérées comme des déchets spé-ciaux. Les symboles chimiques des métaux lourds sont les suivants : Cd = cadmium, Hg = mercure, Pb = plomb. Pour cette raison, veuillez toujours
déposer les piles / piles rechargeables usagées dans les conteneurs de recyclage communaux.
Garantie
Le produit a été fabriqué selon des critères de qualité stricts et contrôlé consciencieusement avant sa livraison. En cas de défaillance, vous êtes en droit de retourner ce produit au vendeur. La pré-sente garantie ne constitue pas une restriction de vos droits légaux.
Ce produit bénéficie d‘une garantie de 3 ans à compter de sa date d’achat. La durée de garantie débute à la date d’achat. Veuillez conserver le ticket de caisse original. Il fera office de preuve d’achat.
Si un problème matériel ou de fabrication devait survenir dans 3 ans suivant la date d‘achat de ce produit, nous assurons à notre discrétion la répa-ration ou le remplacement du produit sans frais supplémentaires. La garantie prend fin si le produit est endommagé suite à une utilisation inappropriée ou à un entretien défaillant.
La garantie couvre les vices matériels et de fabri-cation. Cette garantie ne s’étend ni aux pièces du produit soumises à une usure normale (p. ex. des piles) et qui, par conséquent, peuvent être consi-dérées comme des pièces d’usure, ni aux dom-mages sur des composants fragiles, comme des interrupteurs, des batteries ou des éléments fabri-qués en verre.
Inleiding
... Pagina 57 Correct gebruik ... Pagina 57 Beschrijving van de onderdelen ... Pagina 57 Technische gegevens ... Pagina 58 Omvang van de levering ... Pagina 58Algemene
veiligheidsinstructies
... Pagina 58 Veiligheidsinstructies voorbatterijen / accu‘s ... Pagina 60
Vóór de ingebruikname
... Pagina 61 Batterij plaatsen / vervangen ... Pagina 61Ingebruikname
... Pagina 62 Lengte meten ... Pagina 62 Meetfouten vermijden ... Pagina 63 Lengtes toevoegen ... Pagina 64 Oppervlakte meten ... Pagina 65 Volumes meten ... Pagina 66 Optellen van oppervlaktes resp.volumes ... Pagina 67 De laatste meetwaarden
weergeven ... Pagina 68 Temperatuurweergave ... Pagina 68 Maateenheid wijzigen ... Pagina 68 Batterijweergave ... Pagina 68 Uitschakelen / automatisch
uitschakelen ... Pagina 69
Storingen oplossen
... Pagina 69Reiniging en onderhoud
... Pagina 69Afvoer
... Pagina 69Ultrasone afstandmeter
Inleiding
Hartelijk gefeliciteerd met de aankoop van uw nieuwe product. U heeft voor een hoogwaardig product gekozen. De gebruiksaanwijzing is een deel van het product. Deze bevat belangrijke aanwijzingen voor veiligheid, gebruik en verwij-dering. Maakt U zich voor de ingebruikname van het product met alle bedienings- en veiligheids-voorschriften vertrouwd. Gebruik het apparaat alleen zoals beschreven en voor de aangegeven toepassingsgebieden. Overhandig alle documen-ten bij doorgifte van het product aan derden.
Correct gebruik
Dit product is bedoeld voor het meten van lengtes en de berekening van oppervlaktes en volumes. Bovendien beschikt het product over een tempe-ratuurmeter. Het product is uitsluitend bestemd voor privégebruik.
Beschrijving van de
onderdelen
1 Ultrasone zender / ontvanger 2 Temperatuursensor 3 FT/M-toets 4 READ-toets 5 RECALL-toets 6 Referentieoppervlakte 7 Libel
8 MODE-toets
9 ON / OFF-toets (AAN / UIT) 10 Display
11 Laserdiode 12 RESET-knop
13 Deksel voor batterijvak 14 Batterijvak
Technische gegevens
Voedingsspanning: max. 9 V (gelijkstroom) Batterij type: 6LR61 (9 V blokbatterij) Meetbereik: 0,6 m – 16 m Meetnauwkeurigheid: +/- 1%Weergave capaciteit: tot 9999,99
Golflengte laser: 635–660 nm, 1 mW
Laserklasse: 2 Ultrasone frequentie: 40 kHz
Meetbereik thermometer: –10 °C – +40 °C (14 °F – 104 °F)
Omvang van de levering
1 Ultrasone afstandsmeter 1 9 V-Blokbatterij 1 Gebruiksaanwijzing
Algemene
veiligheidsinstructies
Maak u voor de ingebruikname van het product vertrouwd met alle bedienings- en
veiligheidsvoorschriften! Geef alle documenten mee wanneer u het product aan derden geeft!
Controleer het product voor de ingebruikname op beschadigingen! Neem een beschadigd product niet in gebruik!
Stel het product niet bloot aan vocht! Het kan hierdoor worden beschadigd.
Dit product kan door kinderen vanaf 8 jaar alsmede door personen met verminderde fysieke, sensorische of mentale vaardigheden of een gebrek aan ervaring en kennis worden gebruikt, als zij onder toezicht staan of geïn-strueerd zijn met betrekking tot het veilige gebruik van het product en zij de hieruit voortvloeiende gevaren begrijpen. Kinderen mogen niet met het product spelen. Reiniging en onderhoud mogen niet door kinderen zon-der toezicht worden uitgevoerd.
Gevaar door laserstraling
LASERSTRALING NIET IN DE STRAAL KIJKEN
LASERKLASSE 2 635–660 nm
Het product bevat een klasse-2-laser. Richt de laserstraal nooit op personen of dieren. Kijk nooit direct in de straal. Een zwakke laserstraal kan al tot oogletsel leiden.
Richt de laserstraal nooit op reflecterende oppervlakken of materialen. Ook een gere-flecteerde laserstraal kan zorgen voor schade aan de ogen.
Veiligheidsinstructies
voor batterijen / accu‘s
LEVENSGEVAAR! Houd batterijen / accu‘s
buiten het bereik van kinderen. Raadpleeg bij inslikken onmiddellijk een arts!
EXPLOSIEGEVAAR! Laad niet
oplaadbare batterijen nooit op. Sluit de batterijen / accu‘s niet kort en / of open deze niet. Daardoor kan de batterij oververhit raken, in brand vliegen of exploderen.
Gooi batterijen / accu‘s nooit in het vuur of water.
Stel batterijen / accu‘s nooit bloot aan mechanische belastingen.
Risico dat de batterijen / accu’s lekken
Vermijd extreme omstandigheden en tempe-raturen die invloed op de batterijen / accu‘s zouden kunnen hebben bijv. radiatoren / direct zonlicht.
Vermijd contact met huid, ogen en slijmvliezen! Spoel in geval van contact met batterijzuur de desbetreffende plekken direct af met voldoende schoon water en raadpleeg onmiddellijk een arts!
DRAAG VEILIGHEIDSHAND-SCHOENEN! Lekkende of
bescha-digde batterijen / accu‘s kunnen in geval van huidcontact chemische brandwon-den veroorzaken. Draag daarom in dit geval geschikte veiligheidshandschoenen.
Als de batterijen / accu‘s lekken, dient u deze direct uit het product te halen om beschadi-gingen te vermijden.
Gebruik alleen batterijen / accu‘s van hetzelfde type. Gebruik nooit nieuwe en oude batterijen / accu‘s door elkaar!
Verwijder de batterijen / accu‘s, als u het product gedurende een langere periode niet gebruikt.
Risico op beschadiging van het product
Gebruik uitsluitend het aangegeven type batterij / accu!
Plaats de batterijen / accu‘s volgens de weer-gegeven polariteit (+) en (-) op batterij / accu en op product.
Reinig de contacten van de batterij / accu en die in het batterijvak, voordat u deze plaatst!
Verwijder verbruikte batterijen / accu‘s direct uit het product.
Vóór de ingebruikname
Verwijder vóór de ingebruikname de bescherm-folie van het display 10 van het product en plaats de meegeleverde batterij.
Batterij plaatsen/vervangen
Als op het display 10 het batterijsymbool verschijnt, is de geplaatste batterij bijna leeg en moet deze worden vervangen. Lege batterijen kunnen de meetresultaten negatief beïnvloeden.
Plaats de batterij op de volgende manier:
Open het deksel 13 van het batterijvak aan de achterkant van het product. Met behulp van de strip die zich aan de binnenkant van