[PDF] Top 20 The effect of metal surface treatment on bond strength interface between metal/cement

... to surface treatments: 1 (Primer): sandblasting with aluminum oxide particles 110 μm (Al2O3) + Alloy Primer (Kuraray); 2 (Cojet): sandblasting with silica oxide particles with Cojet- Sand + Silane ...ESPE-Sil. ... See full document

... to the manufacturers’ instructions. The acrylic discs were positioned on the cement layer and the discs were subjected to 1 kgf (10N) constant load for 2 minutes applied by a ... See full document

... In this sense, dental ceramics offer favorable qualities for oral rehabilitation such as biocompatibility, resistance to chemical degradation, mechanical resistance, low conductivity and thermal diffusivity [4, 5]. These ... See full document

... in the literature on the best approach and longevity of repairs in hybrid ceramics are scarce; therefore, the adhesion of composite resin repairs to the ... See full document

... evaluated the effect of root perforations on the bond strength of fiberglass posts cemented to the root canal with two adhesive systems and resin ... See full document

... aim of this in vitro study was to evaluate the shear bond strength of brackets after pre-treatment with different fluoride ...without treatment; NF: 4 min application ... See full document

... agent of a two-step self-etch adhesive (Clearfil Liner Bond F/CLBF) placed on dentin before polymerization on the shear bond ...surfaces. The specimens were divided into 4 ... See full document

... evaluated the effect of denture base polymer type (heat- and microwave-polymerized), ridge lap surface treatment (with and without methyl methacrylate-MMA etching) and thermocycling ... See full document

... On the other hand, sandblasting as a surface pretreatment reduced the bond strength (Table ...to the possibility of volume loss and changes in the morphology ... See full document

... with the results obtained by the authors in previous studies who reported lowest bond strength values when no cleaning was performed after contamination ...[17,35]. On the other ... See full document

... evaluate the bond strength of different repair treatments for composite resin to aged Y-TZP ...dimensions of 4×4×3 mm), and randomly allocated into nine groups (n=15) according to ... See full document

... coat of Scotchbond Multipurpose adhesive (3 M/Espe) was applied, and the tip of the light- curing unit Radii-cal (SDI, Bayswater, Vic, Australia) was positioned close to the adhesive ... See full document

... in the case of teeth with alloy ...period of ul- trasonic instrumentation cannot be avoided during active periodontal treatment, in a single tooth the sum of periods of ... See full document

... slices. The lumens were filled with MTA-A or BD: 60 for each cement (30 uncontaminated and 30 blood ...out bond strength to dentin was assessed at 24 h (n=10), 7 days (n=10) and 28 days ... See full document

... regards the effectiveness of phosphoric acid application before adhesive application, although there was higher shear bond strength in this group (G6), it did not differ significantly from ... See full document

... Abstract: The purpose of this study was to investigate the effect of CPP-ACP treatment and Nd:YAG laser on microtensile bond strength (µTBS) of ... See full document

... After surface treatments or not (control), two cylindrical silicon matrices were positioned on the zirconia ...surfaces. The dual- cure resin cement (Panavia F ...to the ... See full document

... as the microshear bond strength of a self-etching adhesive (Clearfil SE, Kuraray) to eroded dentin, exposed or not to cigarette ...no treatment (control) (C); erosion (E); erosion + ... See full document

... expose the subjacent ...dentin surface was obtained. The root of each tooth was removed about 2 mm above the cementum-enamel junction using the same saw machine cut parallel to ... See full document

... bjective: The purpose of this study was to assess the inluence of conditioning methods and thermocycling on the bond strength between composite core and ... See full document