In addition, the CE mark guarantees that our devices fully comply with the requirements of the European Machinery Directive in terms of safety. 2006/42/CEDirective Macchine / Machine Directive / Machine Directive / Maschinenrichtlinie 2006/95/CEDirective Bassa Tensione / Low voltage Directive / Base Tension / Niederspannungsrichtlinie.
General standards
Made with copper pipes and aluminum fins that are blocked by mechanical expansion of the pipes. The panel must be mounted on the wall; it must be used in 4-pipe and 2-pipe systems and systems with 2-pipes with resistance, with the possibility of connecting two ON - OFF type valves for cutting off the flushing supply water. The following charts determine the pressure drop of the filters with different levels of contamination.
The validity of the warranty is void in the event of non-compliance with the above instructions. Upon receipt of the unit, a visual inspection must be carried out to check that no damage has occurred during transport. By operator we mean a person authorized by the owner of the machine to carry out operations on it (in accordance with what is stated in this manual).
Installation, start-up, shutdown and maintenance of the device must be carried out in accordance with what is indicated in the technical documentation of the product and in any case in such a way that no risk situation arises. The device is designed to minimize the risk to the safety of the people who interact with it. INSTALLATION OF THE DEVICE The essential indications for correct installation of the device are given below.
Completion of all operations, according to specific requirements, is left to the experience of the installer. When performing a vertical installation, the screws that fix the brackets will be in the shortest part of the holes. 10% of the rated voltage of the machine's power supply (for unbalanced three-phase unit maximum 3% between phases).
All electrical work must be carried out by STAFF WITH THE QUALIFICATIONS REQUIRED BY LAW, properly trained and informed of the risks associated with these operations. Use the connectors marked with the grounding symbol to ground the unit and other accessories to the building. The electric motors are connected to the terminal plates mounted inside the unit for TUN 10-10P-15 and to the screw feeder of one of the fans for TUN P units.
The panel must be mounted on the wall; used in 4-pipe and 2-pipe systems and 2-pipe systems with resistance, with the possibility of connecting two ON-OFF type valves to cut off the supply of water coils. We recommend that you provide a machine book (not provided, but the responsibility of the user), which allows you to keep track of the interventions carried out on the unit. It provides that the disposal of the unit is carried out in accordance with the standards in force in various countries.
The lifespan of some of the key components depends on the maintenance they have received.
Descrip on of the unit
Descrip on of components
Confi gurator
Accessories
Accessory coupling
Horizontal installa on “2 dampers”
Horizontal installa on “single fl ow 2 front dampers”
Horizontal installa on “3 dampers”
Technical data
Weight of accessories
For units with different configurations or accessories, reduce the usable static pressure by the pressure drop values of the added components. Air conditioning units of the TUN series are intended for civil, business and hotel systems in small to medium-sized environments. The instructions together with all related documentation must be handed over to the system user, who assumes responsibility for keeping the instructions so that they are always at hand in case of need.
All personnel involved must have a thorough knowledge of the procedures and potential hazards that may occur while the installation procedures are being performed. It is mandatory to use an omnipolar magnetic disconnect switch in accordance with IEC-EN standards (contact opening at least 3 mm), with the appropriate breaking capacity and differential protection installed based on the electrical data table below. as close to the device as possible. Use cable glands to route the main power supply cable and other external connection cables for which the installer is responsible.
The characteristics of the electrical lines and of the related components must be determined by PERSONNEL QUALIFIED TO DESIGN ELECTRICAL SYSTEMS, in accordance with the international and national regulations of the place of installation of the unit and in accordance with the regulations. in effect at the time of installation. Use the book to record date, type of intervention made (routine maintenance, inspection or repair), description of the intervention, measures activated, etc.
Yields and temperatures diff erent from the
TUN 10 with 4-row coil
TUN 10 with 6-row coil
TUN 10p with 4-row coil
TUN 10p with 6-row coil
TUN 15 with 4-row coil
TUN 15 with 6-row coil
TUN 20 with 4-row coil
TUN 20 with 6-row coil
TUN 25 with 4-row coil
TUN 25 with 6-row coil
TUN 40 with 4-row coil
TUN 40 with 6-row coil
TUN 40P with 4-row coil
TUN 40P with 6-row coil
By machine owner we mean the legal representative of the company, body or physical person that owns the system on which the Aermec unit is installed.
Yields and temperatures diff erent from the nominal
Ven la on characteris c curves
TUN 10 - 4 rows
TUN 10P - 4 rows
TUN 15 4 rows
TUN 20 - 4 rows
TUN 25 - 4 rows
TUN 40 - 4 rows
TUN 40P - 4 rows
Pressure drops of fi lters due to fouling
Pressure drop of bag fi lters due to fouling
Opera onal limits
Sound data
Dimensional data
General warnings for installer
Preserva on of the documenta on
Warnings regarding safety and installa on standards
Brackets for wall or ceiling mounting are included with the unit. The anti-vibration joint must be screwed to the plate with self-tapping screws, avoiding tension joints during operation; Before connecting the device to the mains, make sure that the disconnect switch is open.
Identify the terminals for the electrical connection, refer only to the connection diagram supplied with the unit. For installation requirements refer only to the electrical diagram supplied with the device. The electrical diagram together with the manuals must be kept in good condition and ALWAYS AVAILABLE FOR ANY FUTURE SERVICE ON THE UNIT.
General safety prescrip ons
Installa on
Minimum technical spaces
For electrical connections, use double-insulated cables in accordance with the standards applicable to this subject in different countries.
Installa on of the unit
Aeraulic connec ons
Hydraulic connec ons: draining condensa on
Hydraulic connec ons: water coil
Reposi oning of internal components
Water hea ng or cooling coil
Electric connec ons
Specifi ca ons of the connec on cables
Connec on to mains power supply
Electric ba ery connec on
Electric motor connec on
Connec on with electronic thermostat WMT05
Connec on with control panel WMT10
Maintenance
Rou ne maintenance
Maintenance of fi lters if present
Maintenance of fans
Maintenance of coils
Disposal of unit
Accessory dimensional data
Mixing chamber 2 dampers “M2S”
Mixing chamber 3 dampers “M3S”
So bag fi lter sec on “FTF”
Sec on with post-hea ng coil “PBE”
Module with silencer baffl es “SSL”
Return ven la ng sec on with a g4 fi lter “VRF”
Intake damper “SAS”
Flow grid with adjustable louvers “GMD”
Intake grid “GAP”
Plenum with circular fl ow a achments “PMM”
Closed fl ow plenum “PMC”
Motor/s wiring diagram
TUN 10
TUN 10P 15
TUN 20 25
TUN 40 40P
Control panel wiring diagram
TUN 10 with WMT5
TUN 10 with WMT10
TUN 10P - 15 with WMT5
TUN 10P - 15 with WMT10
TUN 20 with WMT5
TUN 20 - 25 with WMT10
TUN 40 with WMT5
TUN 40 with WMT10
A er-sales services
