This kit (L/N/Earth) is used when the power supply of the indoor unit and the outdoor unit is separated.

E-101

OPTIONAL PARTS

This kit (L/N/Earth) is used when the power supply of the indoor unit and the outdoor unit is separated.

(For PUHZ applications only)

Photo

Specifications

PSA-RP·KA series PCA-M·KA series

Power Supply Terminal Kit PAC-SG96HR-E

Unit : mm

Descriptions

Applicable Models

Dimensions

for new A-Control indoor units (L/N/Earth)

N L

53.8 24

39.2 120

Connector 2P (Blue)

Denatured melamine Terminal block material

30A/330V Terminal block capacity

Terminal block (with lead wires connect- ed) x 1, Screw x 1, Fastener (for binding lead wires)

Parts composition

OPTIONALPARTS

This kit (L/N) is used when the power supply of the indoor unit and the outdoor unit is separated.

(For PUHZ applications only)

Photo

Specifications

PCA-RP71HAQ PEAD-M·JA series

Power Supply Terminal Kit PAC-SG97HR-E

Unit : mm

Descriptions

Applicable Models

Dimensions

for new A-Control indoor units (L/N)

L N

36 18.5

38 80

Connector 2P (Blue)

Denatured melamine Terminal block material

15A/264V Terminal block capacity

Terminal block (with lead wires connect- ed) x 1, Screw x 1, Fastener (for binding lead wires)

Parts composition

E-103

OPTIONAL PAR

TS

Power Supply Terminal Kit for new A-Control Indoor units PAC-SG96,97HR-E

How to Use / How to Install

1. Overview

This kit is used when the power supply of the indoor unit and the outdoor unit is separated.

(for PUHZ applications only)

Refer to the installation manual of the indoor unit as well.

2. Provided parts

Comfirm the following parts are included.

Terminal block (lead wires already wired) x 1 Screw (to attach terminal block) x 1 Fastener (to tie lead wires) x 1 Screw (to secure ground wire) x 1

For PAC-SG96HR-E For PAC-SG97HR-E For PAC-SG96HR-E only

1:1 System

Simultaneous twin/triple/four system

L N

S1 S2 S3

S1 S2 S3 1 2 L N

<For models without heater>

•The indoor power supply terminal kit is required.

•Affix a label B that is included with the manuals near each wiring diagram for the indoor and outdoor units.

•Affix a label B that is included with the manuals near each wiring diagram for the indoor and outdoor units.

AOutdoor unit power supply BEarth leakage breaker

CWiring circuit breaker or isolating switch DOutdoor unit

EIndoor unit / outdoor unit connecting cords FRemote controller

GIndoor unit HOption

JIndoor unit power supply

<For models without heater>

•The indoor power supply terminal kits are required.

AOutdoor unit power supply BEarth leakage breaker

CWiring circuit breaker or isolating switch DOutdoor unit

EIndoor unit / outdoor unit connecting cords FRemote controller

GIndoor unit HOption

JIndoor unit power supply KIndoor unit earth

A B C J B C H

E

E

F

F D

D G

K K K

H G

G H

G H

G H

L N L

N

S1 S2 S3 S1

S2 S3

1 2

L N

S1 S2 S3 1 2

L N

S1 S2 S3 1 2

L N

S1 S2 S3 1 2

A B C J B C

N

L N

L NN

2 1

2 1

3 3

Change the yellow and blue relay connectors.

Terminal block attachment hole Terminal block attachment hole

Relay connector (blue) Relay connector (blue)

Relay connector (yellow)

Relay connector (yellow) 44

3. Attachment method

■ PAC-SG96HR

1.Remove the cover of electric parts

box. 2. Attach terminal block 1 using screw

2 in the direction shown in the figure.

3. Change the relay connectors of blue and yellow lead wires, secure the ground wire using screw 4 at the position shown in the figure, and then bundle the lead wires using fastener 3.

Ceiling suspended, PCA-M∙KA type:

OPTIONALPARTS

Terminal block attachment hole Terminal block attachment hole

Relay connector (yellow)

Relay connector (yellow)

Relay connector (blue) Relay connector (blue)

Change the yellow and blue relay connectors.

1

1 2 2

3 3

1 2 2 1

Relay connector (blue)

Relay connector (blue)

Relay connector (yellow) Relay connector (yellow)

Change the yellow and blue relay connectors.

1.Remove the terminal block cover of electric parts box.

■ PAC-SG97HR

Ceiling suspended for kitchens, PCA- RP 71HA Q type:

2. Attach terminal block

using screw

3. Change the relay connectors of blue and yellow lead wires, and then bundle the lead wires using fastener

.

3.Change the relay connectors of blue and yellow lead wires.

T

Terminal block attachment hole erminal block attachment hole

Ceiling concealed, PEAD-M.JA type 1.Remove the cover of electric parts

box.

2. Attach terminal block 1 using screw

in the direction shown in the figure.

Power Supply Terminal Kit for new A-Control Indoor units PAC-SG96,97HR-E

E-105

OPTIONAL PAR

TS

4. Electric wiring

Be sure to do the electric wiring following the steps in each indoor unit installation manual.

6. DIP switch settings of the outdoor unit control board

It is necessary to change the settings of DIP switch on the outdoor unit control board.

7. Test run

Perform a test run following the steps in the installation manual of the outdoor unit.

5. Paste the labels enveloped in the instruction document of indoor unit near the electric wiring diagrams of both indoor and outdoor units.

Three types of labels (labels A-C) are provided: Paste the label B.

(Separate indoor unit/outdoor unit power supplies... Label B)

ON OFF 1 2

3

<SW8>

Outdoor unit DIP switch settings (when using separate indoor unit / outdoor unit power supplies only)

Change of connectors (except PCA-M·KA type)

(PCA-M·KA type)

Indoor unit control board

Connectors (connections of initial setting are for indoor unit power supplied from outdoor unit)

Connectors Indoor unit power supplied from outdoor unit

(initial setting)

BLACK CN01

L ^BLUE

YELOW YELOWBLUE CN01

Option

S1 S2 S3 N

L

S1 S2 S3 N

Indoor unit control board

Separate indoor unit / outdoor unit power supplies BLACK CN01

BLUE

YELOWBLUE YELOW CN01

Option

If the indoor and outdoor units have separate power supplies, change the connections of the connectors as shown in the following figure.

Indoor unit control board

Connectors Indoor unit power supplied from outdoor unit

(initial setting)

ORANGE CND

L ^BLUE

YELOW YELOWBLUE CND

S1 S2 S3 N

L

S1 S2 S3 N

Indoor unit control board

Separate indoor unit / outdoor unit power supplies ORANGE CND

BLUE

YELOWBLUE YELOW CND

Connectors (connections of initial setting are for indoor unit power supplied from outdoor unit) Option

If the indoor and outdoor units have separate power supplies, change the connections of the connectors as shown in the following figure.

Power Supply Terminal Kit for new A-Control Indoor units PAC-SG96/97HR-E