FlowCon FT.0.2, FT.0.3 and FT.0.4 actuators

INSTALLATION AND OPERATION INSTRUCTION

1B95050 - P100006323

Brasil Singapore . 03/2014

FlowCon International assumes no responsibility for mistakes, if any, in any printed material.

Denmark Dubai USA

THERMAL ACTUATORS FlowCon FT actuators

- 1 -

FlowCon FT.0.2, FT.0.3 and FT.0.4 actuators

360º Figure 2 Figure 1



A 20625-00 FT.0.3

1403

MadeinGerman y 230 V NC 1,2 W



A 20625-00 FT.0.3

1403

MadeinGerman y 230 V NC 1,2 W A 20625-00 FT.0.3

1403

MadeinGerman y 230 V NC 1,2 W



A 20625-00 FT.0.3

1403

MadeinGerman y 230 V NC 1,2 W



A 20625-00 FT.0.3

1403

MadeinGerman y 230 V NC 1,2 W

>click<

The actuator type FlowCon FT.0.2 is a thermal mo- dulating actuator, NC. FlowCon FT.0.3 and FT.0.4are thermal ON/OFF actuators, NC.

Fitting the FlowCon FT actuator:

Actuators are supplied with a separate black colored adaptor ring. First, screw on the adaptor ring finger

tight to the connection thread at the top of the insert.

Do not use additional tools (figure 1,



^and



^{). For}

FlowCon FT.0.2 connect the cable before fitting the actuator on to the adaptor ring. FlowCon FT.0.3 and FT.0.4 comes with fixed cable and can be fitted im- mediately onto the adaptor ring (



). A click noise will indicate that the actuator is fitted correctly (



).

Removing the FlowCon FT actuator:

Actuators are equipped with a front push button to activate the release mechanism. When pushed, the actuator is released and can be removed from the adaptor ring. A special feature on the FlowCon FT.0.2 will allow the actuator to become tamper proof as the bush button can be removed for protection.

Installation of the FlowCon FT actuator:

To ensure that the valve is in an open position during commissioning of the system, all mentioned actuators will be delivered in a Normally Open position and re- main in this position until they are electrically operat- ed first time. FIRST TIME POWERING requires ope- rating voltage applied for approximately 6 minutes.

Upside down installation is allowed for all FT-actua- tors along with the standard horizontal and vertical installation (figure 2).

Denmark Dubai USA

1B95050 - P100006323 Brasil Singapore . 03/2014

FlowCon International assumes no responsibility for mistakes, if any, in any printed material.

THERMAL ACTUATORS FlowCon FT actuators

- 2 -

Blue Black Red

FT.0.2 Actuator

Power 24V AC Ground/common 0-10V DC

Blue Brown

FT.0.3 / FT.0.4 Actuator

Power Ground/common

24V AC/DC 230V AC Open

Close Figure 3

Connection and actuator wiring:

For power supply, use safety isolating transformer according to EN 61558-2-6 (Europe) or class II (North America) and for FlowCon FT.0.2 also with a maximum power output of 100VA.

Wiring diagram for actuator type FT.0.2 (24V AC), FT.0.3 (230V AC) and FT.0.4 (24V AC/DC) are shown in figure 3.

Warranty obligation:

Failure to abide by all recommendations as per this installation and operation instruction will void warranty.