Lubrication and Lubricants
Improvement in Surface Quality with Solid Lubrication in Hard Turning
... tool and workpiece interaction can be minimized by providing effective lubrication, the heat generated can be reduced to some ...solid lubricants, which can sustain and provide lubricity over ...
5
Mat. Res. vol.17 número5
... biolubricant and to add oxide nanoparticles (ZnO and CuO) in order to improve abrasion resistance and ...biodegradable and has better performance under boundary ...(soybean and ...
5
Wear and Friction Behavior of Stir Cast Al-TiB2 Metal Matrix Composites with Various Lubricants
... of lubrication film in the contact interface between the composites and steel, and the interaction of the surfaces with the lubricant ...the lubrication film depends on the composition ...
14
Suitability of Alternative Lubricants for Automotive Gear Applications
... hydrogen and other groups with carboxylic acid at the terminal ...bonds and polyunsaturated for six and more bonds in ...properties and performance for particular vegetable oil depends lot on ...
4
Effect of Cup Deflection on Friction of Hip Resurfacing Prosthesis with Various Clearances Using Blood and Clotted Blood as Lubricants
... elastohydrodynamic lubrication and avoid equatorial seizing is still being studied and debated, tribologists recommend that the diametral clearance be as small as possible in large-diameter bearings ...
3
Effects of Couple Stress Lubricants on Pressure and Load Capacity of Infinitely Wide Exponentially Shaped Slider Bearing
... hydrodynamic lubrication has involved the use of the Reynolds equation and the finite difference method ...distribution and ensured significant load carrying ...in lubricants blended with ...
6
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número4
... interface lubrication between punch and sheet metal and deformation rate, among ...The lubricants used ranged from liquid, such as mineral and vegetable oils with extreme pressure ...
5
Portable Lubrication Analytical Instrumentation for Maintenance Application
... Abstract —Maintenance practices have a beneficial economic impact in industry. Industrial equipment operators are continuously forced to reduce operating costs while increasing profits to remain competitive. Reaching ...
6
J. Braz. Soc. Mech. Sci. & Eng. vol.29 número1
... friction and wear of the sliding ...both lubricants and components ...in lubrication mode occurring in the tribometer to real ...the lubrication adequacy of the ...on lubrication ...
8
Polímeros vol.26 número4
... oil and at a temperature of 85 ± 5 °C inside the test ...other and moved on the same ...monitored and compared with the nominal force of approximately 118 N (equivalent to an apparent contact ...
7
Performances Of 6-Pocket Compensated Conical Hydrostatic Journal Bearing Under Micropolar Lubrication
... generated and globalized as per the connectivity of the ...� and ̅ � are calculated. Using the values of ̅ � and ̅ � , the correction in journal center is established and also the journal ...
6
Health And Wellbeing Impact And Treatment of Nocturia – A Review of The Literature
... The aetiological factors implicated in nocturia can be classiied as afecting urine storage, urine production, and unrelated conditions that impact upon sleep. Lower urinary tract dysfunctions that lead to a ...
6
Transinformação vol.26 número3
... Serie Temporal: El dominio vegetable oil combustion está compuesto por un total de 211 patentes concedidas por la USPTO entre 1976 y el 10 de diciembre del año 2013. El análisis de la razón de variación de la producción ...
13
Hard-on-hard lubrication in the artificial hip under dynamic loading conditions.
... film lubrication regime over the whole gait cycle and shows, as expected, an even and regular pattern of the lambda ...(boundary lubrication) exist which may be the cause for increased ...
8
Mat. Res. vol.17 número1
... dimensional and geometric ...workpiece and wheel), can be considered a factor of extreme importance when it comes to roundness ...friction and improve the part inal quality, cutting luids with good ...
10
The influence oil film lubrication of the piston-cylinder dynamic
... Reynolds and moving of piston are ...hydrodynamic lubrication model, was applied to M501 diesel ...pin and lubricant viscosity, underscoring their importance in engine de& ...
7
Evaluation of different methods of cooling-lubrication in cylindrical grinding of advanced ceramic dip
... oil and machined chips), which increases also wheel wear, as should be discussed ...cycles, and for all equivalent cut thicknesses, and can explain the differences between tangential cutting forces ...
12
Analysis of the Influence of Sparkout Time on Grinding Using Several Lubrication/Cooling Methods
... geometric and dimensional ...operation and included the Minimum Quantity Lubrication (MQL) technique, which has proved to be an environmentally correct alternative, combining a small amount of ...
5
Influence of the Previous Preheating Temperature on the Static Coefficient of Friction with Lubrication
... of the force of friction related to slip arises and, therefore, surface films can manifest their influence. The temperature elevation affects all of the above listed factors, since it favours a decrease in the ...
5
Application of the Minimum Quantity Lubrication (MQL) Technique in the Plunge Cylindrical Grinding Operation
... positioning and rigidity of the machine- workpiece-tool system, allowing the production of high precision parts with low dimensional ...alternative lubrication and cooling ...Quantity ...
4