[PDF] Top 20 Nd:YAG laser influence on bond strength of adhesive resin to dentin

... self-adhesive resin luting cement, RelyX Unicem, had the lowest mean μTBS values compared to the other two adhesive ...this resin cement interacts more superfi cially with the ... See full document

... form of gel, obtained from different granulations and concentrations of the powder of this biomaterial; in surgical sites, or in non- surgical periodontal therapy [12], as well as for the control ... See full document

... results of this study showed that different drying times influence the bond strength results of the adhesive systems when considering the immediate test condition, rejecting the ... See full document

... self-etch adhesive, All-Bond SE, pH = ...according to the manufacturer’s recommendations, after the surfaces were dried by means of a compressed air syringe at a distance of 5 cm from ... See full document

... techniques on the push-out bond strength and on the presence of bubbles at the interfacial area between the post and dentin ...the bond strength and the percentage ... See full document

... into resin cement. Thus, the treatment of the dentin and of the restorative material was efficient, causing intrinsic rupture of the resin ...the resin cement did not ... See full document

... Single Bond 2), irradiação com Nd:YAG laser (60 s, 1064 nm, 10 Hz) nos parâmetros de energia de 60 e 100 mJ/pulso e fotopolimerização (10 ...do laser, 100 mJ apresentou maiores médias de RA quando ... See full document

... patterns on the dentin surfaces [6], which can positively influence the dentin bond strength of Single Bond adhesive ...movement of the dental ... See full document

... out to investigate the application of ozone to hard tissues and ...characteristics of enamel, nor did it negatively affect microleakage or sealant ...application of ozone to ... See full document

... worn to expose an area of dentin and were divided into 2 groups: Group C (Control) - acid etching with 37% phosphoric acid + Single Bond; Group CHX ...Single Bond. Blocks of ... See full document

... submitted to tensile bond strength testing in a universal testing machine, EMIC DL- 2000 (EMIC, São José dos Pinhais, PR, ...attached to the base of the universal testing machine, while ... See full document

... used to assess the dentine bond strength of the resin- dentine ...micro-tensile bond strength approach (Van Meerbeek et ...important to mention that bond ... See full document

... enamel/ dentin surface to maintain curing distances of 3 or 6 ...matrix of 4 mm in width and 6 mm n length was placed on the surfaces and two layers (2 mm thick) of resin ... See full document

... epoxy resin. The bond interfaces were polished with 400-, 600-, 1000- and 1200-grit silicone carbide abrasive papers and wetted with water using manual pressure and rotary ...pastes on a felt disk ... See full document

... the bond strength of softened dentin was not affected by the application of any type of CPP-ACP based ...related to the 10-MDP (10 - methacryloxydecyl dihydrogen ... See full document

... Shear bond tests were performed with a universal testing machine (UTS 20K, UTS Testsysteme GmbH & Co KG, Germany, Ulm) on the next ...transferred to the specimens was accomplished with a bevelled ... See full document

... values of the shear bond tests, performed in this study, exposed a weak bond strength to ...application of the adhesive and first layer of ...followed to ... See full document

... modification of the bonding substrate with chitosan and riboflavin increases the mechanical properties, enhanced the mechanical stability of demineralized dentin substrates against hydrolytic and ... See full document

... regarding to bond strength with resin ...composite resin with adhesive systems (14) and evaluated the cutting effectiveness, showing that ultrasonic diamond bur had less dental ... See full document

... When LASER preparation is performed no smear layer is formed, which may be beneficial for simplified adhesives, as smear layer could otherwise buffer the less acidic monomers, preventing monomer infiltration  ... See full document