• Nenhum resultado encontrado

J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1

N/A
N/A
Protected

Academic year: 2018

Share "J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1"

Copied!
1
0
0

Texto

(1)

Analysis of a Porous Exponential Slider Bearing Lubricated with a …

J. of the Braz. Soc. of Mech. Sci. & Eng. Copyright © 2003 by ABCM July-September 2003, Vol. XXV, No. 3 / 265

ERRATA

The following are the corrections in the paper entitled " Analysis of a Porous Exponential Slider Bearing Lubricated with a Ferrofluid Considering Slip Velocity by Rajesh C.Shah and M.V.Bhat" published in Vol. XXV, No.3, July-September 2003.

1. Equation (1) should read as

(

)

{

(

)

}

0

M 2 ρα µ

ζ p

2 0

2 =

⎥⎦ ⎤ ⎢⎣

× × × ×

∇ + ∇ • + ∇ + ∇

q M H M q M

2. Equation (9) should read as

3. Equation (11) should read as

⎥ ⎥ ⎦ ⎤ ⎢

⎢ ⎣ ⎡

+ρα µ ζ

− + ζ

=

⎥ ⎥ ⎥ ⎥ ⎥

⎦ ⎤

⎢ ⎢ ⎢ ⎢ ⎢

⎣ ⎡

⎟ ⎠ ⎞ ⎜

µ µ

⎪ ⎪ ⎭ ⎪ ⎪ ⎬ ⎫

⎪ ⎪ ⎩ ⎪ ⎪ ⎨ ⎧

⎟⎟⎠ ⎞ ⎜⎜⎝

ζµ ρα − +

ζ µ

ρα − + +

sh 1

/ ) ksH (

) sh 2 ( h dx

d U 6

H 2 1 p dx

d

2 H 1

) sh 1 (

/ ) H ksh 3

( ) sh 4 ( h kH 12 dx

d

2 2 0 2

2 2 3

*

2 1 * 2 1 0 *

2 1 2

2 1 1 3 1 *

h k 6 , U KAh

, UA

p h p , 2

A K sh

s , h

h h , h kH , A x X

= γ ζ µ µ = µ

ζ = ζ

µ ρα = β = = =

Ψ =

=

(9)

Referências

Documentos relacionados

Using rapid molds, pre-series of parts are obtained in record time with the injection molding material chosen to manufacture the final parts.. So, tests may be extended to a

Samples cut from tensile test specimens in the tension axis direction were used for dilatometry tests, performed in an Adamel Lhomargy LK02 equipment, in the temperature range from

The bedform evolution predicted by the model agrees with the stability analysis, showing the existence of a most unstable mode (the growth rate has a maximum)

Normal flux percentage mean error on face 4 versus Peclet number, for a boundary element mesh with one hundred and sixty elements, for example 1.. Fortunately,

The condition 1G also presented full penetration, but the root of the weld has shown dropout (liquid flow) due to the excessive power. Since the resulting microstructure

The centralized cross position between grinding wheel and specimen is associated with the Y-axis of the grinding machine so that the procedure receives the name

Based on the full factorial design (3 4 ), a total of 81 experiments, each having a combination of different levels of variables, are carried out to study the effect

On the other side, the surface finish in the turning process is influenced by a number of factors, such as: cutting speed, feed rate, depth of cut, material