Bond Strength
Research Article Micro-Raman Vibrational Identification of 10-MDP Bond to Zirconia and Shear Bond Strength Analysis
... the bond of 10-MDP to zirconia and microshear bond strength to zirconia varied ceramic primer and (2) evaluation of Raman peak related to the bond of 10-MDP to zirconia and microshear ...
8
Tensile bond strength of self-etching versus total-etching adhesive systems under different dentinal substrate conditions
... dentin bond- ing. The aim of this study was to compare the tensile bond strength to dentin of three adhesive systems, two self-etching ones (Clearil SE Bond - CSEB and One Up Bond F - ...
6
Effect of fluoride solutions on the shear bond strength of orthodontic brackets
... shear bond strength of orthodontic devices refer to the use of fluoride incorporated into prophylactic pastes (9,10) related to restorative materials (14) or even on the enamel that underwent severe changes ...
5
Bond strength of adhesive systems to human tooth enamel
... & Bond 2.1), a self-etching primer (G2 Clearil SE Bond), and a self-etching adhesive (G3 One Up Bond F), through shear bond strength to enamel of human teeth, evaluating the type of ...
6
BOND STRENGTH DURABILITY of SELF-ETCHING ADHESIVES and RESIN CEMENTS TO DENTIN
... microtensile bond strength ( μTBS) of one- (Xeno III, Dentsply) and two-step (Tyrian-One Step Plus, Bisco) self-etching adhesive systems bonded to dentin and cemented to chemically cured (C&B Metabond) ...
6
Evaluation of Resin Bond Strength to Yttria-stabilized Tetragonal Zirconia and Framework Marginal Fit: Comparison of Different Surface Conditionings
... The purpose of this study was to evaluate the effect of different surface treatments of yttria- stabilized tetragonal zirconia (Y-TZP) on bond strength durability and marginal discrepan- cies. For adhesion ...
14
Effect of temporary cements on the shear bond strength of luting cements
... The results of the present showed that that the presence of eugenol may either increase or reduce the bond strength of final cementation, depending on the composition of the resin luting cement used. ...
7
Bond strength of different endodontic sealers to dentin: push-out test
... Conclusion: Epiphany sealer presented higher bond strength values to dentin in both irrigating protocols, and the use of 2.5% NaOCl and 17% EDTA increased the bond strength values for [r] ...
4
Tooth whitening affects bond strength of adhesive systems in enamel
... the bond strength of the specimens, measured by microtensile tests, remained statistically unaltered as compared to the bond strength values obtained before ...same bond strength ...
8
Bond strength between acrylic resin and maxillofacial silicone
... It is interesting to note that the application of the Silastic Medical A adhesive did not improve the bond strength between the acrylic resin and facial silicone (Table 3). The adhesive had no complete ...
6
Bond strength of a composite resin to an adhesive luting cement
... shear bond strength of a composite resin (CR), previously submitted to the application of a temporary cement (TC), to an adhesive luting ...shear bond strength ...shear bond ...
5
Bent´s rule contextualizes hydrogen bond strength in trimolecular clusters.
... ou mediante hibridização de orbitais com diminuição ou aumento no caráter s do elemento X dependendo se o sistema for fracamente ou fortemente ligado com surgimento dos efeitos red-shift ou blue-shift, respectivamente. ...
8
Rev. IBRACON Estrut. Mater. vol.1 número1
... low strength CC and SCC tests results, they usually present similar bond strength [21-23], except in places with high reinforcement rates, where SCC stands out ...the bond displace- ment ...
13
Friction Surfacing In Steel 304
... good bond on plane surfaces but also on other contours by design of special purpose machines using CNC ...Since bond strength is very good, these deposits are expected to serve better during ...
14
Braz. Dent. J. vol.22 número6
... The results of OptiBond All-In-One, however, were similar to those of Adper SE Plus and Clearfil 3S Bond, both containing 20% HEMA. One can assume that other factors, such as the solvent type and content, may have ...
5
Braz. Dent. J. vol.21 número6
... The aim of this study was to assess the influence of etching and light-curing time on the shear bond strength (SBS) and adhesive remnant index (ARI) of a resin-modified glass ionomer cement (RMGIC) upon ...
5
Avaliação da cimentação de pinos não metálicos na dentina intraradicular utilizando cimentos resinosos auto-adesivos
... the bond strength between the post and the resin cement, many surface pretreatment procedures for posts have been investigated that involve the use of mechanical or chemical ...the bond ...
115
Dental Press J. Orthod. vol.22 número4
... shear bond strength values were evaluated as regards the normality by the Shapiro-Wilk test and homoscedasticity of the variances by the Bartlett ...
7
Braz. Dent. J. vol.28 número1
... Effect of Enamel and Dentin Surface Treatment on the Self-Adhesive Resin Cement Bond Strength.[r] ...
2
Braz. Dent. J. vol.19 número3
... shear bond strength (SBS) of etch-and-rinse (Adper Scotch Bond Multi Purpose - ASBMP and Adper Single Bond 2 - ASB2) and self-etching (AdheSe -AD and Adper Prompt - AP) adhesive systems after ...
5