AISI 304 stainless steel
Nickel-Titanium Alloys Welding of Thin Sheets Using GTAW: Comparative Study Between Similar and Dissimilar Welding with AISI 304 Stainless Steel
... with AISI 304 stainless steel using the Gas Tungsten Arc Welding (GTAW) process and to study the mechanical and metallurgical properties of the joints with and without post-welding heat ...
8
Analysis of correlations of multiple-performance characteristics for optimization of CO2 laser nitrogen cutting of AISI 304 stainless steel
... The identification of laser cutting conditions for satisfying different requirements such as improving cut quality characteristics and material removal rate is of great importance. In this paper, an attempt has been made ...
6
Welding of AA1050 aluminum with AISI 304 stainless steel by rotary friction welding process
... Vickers microhardness values measured in the side of AA1050 aluminum and in the side of AISI 304 stainless steel, near the bonding interface, central region, were higher than in the metal ...
6
Influence of Temperature on Mechanical Properties, Fracture Morphology and Strain Hardening Behavior of a 304 Stainless Steel
... The strain hardening behavior of an AISI 304 stainless steel at different temperatures was investigated in this work. Specimens were tensile tested up to rupture at temperatures of 25, 50, 75, ...
11
Soldag. insp. vol.21 número2
... In stainless steels, microstructural damage is caused by precipitation of chromium carbides or sigma ...in stainless steel welds because they lead to weld ...of stainless steel ...of ...
9
Selective Surfaces of Black Chromium for Use in Solar Absorbers
... One of the applications of selective surfaces is to improve performance of solar absorbers. The purpose of this work is to produces selective coatings with high absorption of solar radiation in the range of UV/Vis/NIR. ...
5
REM, Int. Eng. J. vol.70 número3
... the AISI 304 stainless steel has high corrosion/oxidation resistance, its tribological properties are poor, being one of the barriers for use in severe wear ap- ...for AISI 304 ...
6
Innovative low temperature plasma approach for deposition of alumina films
... 3 deposited amorphous alumina coatings on AISI 304 stainless steel substrates by the metal organic chemical vapor deposition (MOCVD) in a hot wall reactor at 380 °C with oxygen in the[r] ...
10
J. Braz. Chem. Soc. vol.14 número4
... and AISI 304 stainless steel in aqueous tungstate solutions containing chloride ion was investigated by cyclic voltammetry, open circuit measurements and impedance ...
7
J. Braz. Chem. Soc. vol.15 número4
... on AISI-304 stainless steel by the three coloring ...different steel samples (colored or not); the respective standard deviations for the (E pit - E cor ) values were not shown in this ...
9
art hfgabreu Deformation induced martensitic
... austenitic stainless steels has increased considerably mainly due to nickel price evolution in the last ...modified stainless steel was ...traditional AISI 304 ...
5
ASSESSMENT OF HYDROPHOBICITY AND ROUGHNESS OF STAINLESS STEEL ADHERED BY AN ISOLATE OF BACILLUS CEREUS FROM A DAIRY PLANT Patrícia Campos Bernardes
... For stainless steel AISI 304, #4 and stainless steel AISI 304 # 4 adhered by B. cereus, the contact angles between the surfaces and water, formamide, and ...
9
REPOSITORIO INSTITUCIONAL DA UFOP: Comparative study of high temperature oxidation behaviour in AISI 304 and AISI 439 stainless steels.
... the AISI 304 and AISI 439 steels, between 850 and 950 °C, in oxygen and in Ar-H 2 -H 2 O at- mosphere, ...the AISI 304 steel has less oxidation resistance than the AISI ...
7
Oxidation of AISI 304 and AISI 439 stainless steels
... ferritic stainless steel (AISI 439) containing tita- nium and niobium (see Table ...in stainless steels to prevent the risks of intergranular cor- rosion of weldments, due to the formation of ...
11
art hfgabreu Cold deformation effect
... as-cast AISI 301 stainless ...on AISI 316L austenitic stainless steel corrosion resistance in a medium containing heavy ...turning AISI 304 austenitic stainless ...
10
Mat. Res. vol.17 número5
... The possibility of predicting defect-free weld by analyzing and understanding AISI 304 austenitic stainless steel axial force profiles during FSW, using position- controlled mode, was ...
4
Mat. Res. vol.19 número2
... the steel in the two electrolytes, the aqueous solution of calcium hypochlorite was less aggressive to the studied stainless ...The AISI 304 steel showed a similar transpassive ...
6
REPOSITORIO INSTITUCIONAL DA UFOP: Soldagem a laser dos aços inoxidáveis AISI 304 e AISI 316: análise microestrutural em função dos parâmetros operacionais.
... O fator-chave para procedimentos de desenvolvimento ´e a sele¸c˜ao ´otima das vari´aveis do processo [ 9 ] . Uma investiga¸c˜ao elaborada sobre a otimiza¸c˜ao dos parˆametros opera- cionais visando efeitos na qualidade ...
90
Porous stainless steel for biomedical applications
... massive steel, according with the largest relative density obtained among the sintered ...the steel foams, those produced with 15 ...micrographs, steel foams obtained with 30 ...the steel ...
9