processing parameters
Characterizing the Effect of Processing Parameters on the Porosity of Laser Deposited Titanium Alloy Powder
... Processing parameters in LMD process has been shown to affect properties as well as porosity of deposited part [24]. In this study, the effect of laser power and scanning speed on the percentage porosity ...
5
Effect of Solidification Processing Parameters and Silicon Content on the Dendritic Spacing and Hardness in Hypoeutectic Al-Si Alloys
... thermal parameters, microstructural spacing and mechanical ...solidification processing parameters and solute additions is very important for the industrial solidification processes, due to its ...
8
Sensitivity testing practice on pre-processing parameters in hard and soft coupled modeling
... This paper pays attention to the problem of practical applicability of coupled modeling with the use of hard and soft models types and necessity of adapted to that models data base possession. The data base tests results ...
8
RESEARCH OF THE INFLUENCE OF OZONE AND AIR PROCESSING PARAMETERS ON STERILIZATION OF VEGETABLE SUBSTRATES
... In the article we consider the questions of ozone and air impact on pathogenic microflorastern of products when their production. Results of the statistical analysis allowing to determine optimum parameters of ...
15
Mechanical properties correlation to processing parameters for advanced alumina based refractories
... Surface degradation damage level was established as function of fiber content and number of cycles of thermal shock. The data concerning the pressure used for specimen preparation had much less statistical importance ...
9
Effects of processing parameters on microstructure of semi-solid magnesium alloy
... © 1994-2007 China Academic Journal Electronic Publishing House.. All rights reserved..[r] ...
4
Mat. Res. vol.20 número1
... detailed parameters utilized in this work are shown in Table ...above processing procedures in accordance with the parameters listed in Table 1, the thixoforged composites under diferent ...
13
Mat. Res. vol.6 número2
... laser processing is a desirable welding tech- nique due to processing speed, weld quality and mechani- cal joining ...laser processing parameters such as power and scan- ning speed on the ...
6
Mat. Res. vol.15 número5
... same parameters by Plasma Transferred Arc on a steel substrate and a chilled Cu ...the processing parameters on the microstructure, Iron content, elastic modulus and hardness of Co-based ...
5
Mat. Res. vol.8 número2
... of processing parameters on the magnetic properties of Pr-based sintered magnets prepared using the hydrogen decrepitation process have been ...for processing Pr 16 Fe 76 B 8 magnets have been ...
3
An Investigation on Tool Wear Prediction in Automotive Sheet Metal Stamping Die Using Numerical Simulation
... control parameters involved in the production of automotive ...various processing parameters, such as the lubrication, binder pressure and surface coating, on the critical tool worn area of a certain ...
5
Mat. Res. vol.13 número1
... of processing parameters (slab thickness, water flow of interstand cooling and oil flow in roll gap lubrication system) on the thickness and composition of the tertiary scale formed during hot strip ...
4
Mat. Res. vol.19 número4
... 3.3. An optimization method based on close-cycle control of current in numerical simulation The multi-stage current mode has been proved to be efective for the elimination of the secondary upsetting defect, as stated ...
10
Adaptive control of mechatronic machine-tool equipment
... The 4 th level subsystems differentiate by the specific types and features of control activities which are applied when running these subsystems. A peculiarity of popular NC machine tools is the application of direct or ...
4
ISSN 2349-0837 Volume 5 Number3 Journal of Advances in Agriculture
... Currently, fruit is one of the most competitive segments of the Brazilian agricultural sector. Fresh fruit and its derivatives show an upward trend in exports. The sector‟s potential stems from an increase in consumption ...
12
Effects of different processing technologies on chemical and antioxidant parameters of Macrolepiota procera wild mushroom
... Regarding free sugars composition (Table 4), dried samples gave the highest total content (19.3 g/100 g dw), also presenting the highest levels of mannitol (11.4 g/100 g dw). The highest concentration of trehalose (10.2 ...
25
The GOME-2 instrument on the Metop series of satellites: instrument design, calibration, and level 1 data processing – an overview
... instrument anomalies and instrument degradation can only be mitigated by soft correc- tions which have to be based on evaluation of a consistent dataset. Short to long-term changes in instrument throughput may affect the ...
56
Efeito dos conservantes alimentares sobre as propriedades antioxidantes e qualidade microbiológica de suco de goiaba vermelha
... food processing, because they act as inhibitors of non-enzymatic browning and microbial growth, such as antioxidants and reducing agents, depending on the class ...
9
Cracked green table olive from the south of Portugal: the influence of diferent brining conditons
... of processing table olives according to fermentation conditions (temperature, aeration and salt content) and maturation of fruits (green, turning color or ...
11
MODELING AND SIMULATION OF PARALLEL PROCESSING ARCHITECTURE FOR IMAGE PROCESSING
... image processing applications: low, intermediate, and high-level ...image processing in mind [4,5, 6, 7,8, 9, 10,11, 12, ...image processing applications could be executed on either SIMD or MIMD ...
11