[PDF] Top 20 Effect of Dentin Preparation Mode on the Bond Strength Between Human Dentin and Different Resin Cements

... (Fig.1). The smear layer was thicker when the preparation was done with the coarse diamond bur, producing a more irregular surface with groves compared to the remaining ...(15). ... See full document

... examined the effect of deproteinization on the microtensile dentin bond strength (mTBS) and nanoleakage (NL) of conventional and self-adhesive ... See full document

... evaluate the long-term post push-out bond strength to dentin, water sorption, solubility and swelling of conventional and self-adhesive dual-cure resin ...ARC ... See full document

... aim of this in vitro study was to evaluate the effect of different bur types and acid etching protocols on the shear bond strength (SBS) of a ... See full document

... purpose of this study was to evaluate the effects of long-term storage on the microtensile bond strength (µTBS) to dentin of two self-adhesive and ... See full document

... canal preparation in ...gel and obtained the highest bond-strength values, which were statistically different to the association of NaOCl and EDTA and ... See full document

... bjective: The purpose of this study was to evaluate, by shear bond strength (SBS) testing, the influence of different types of temporary cements on ... See full document

... evaluated the effect of a 2% chlorhexidine-based disinfectant (CHX) on the short-term resin-dentin bond strength of a self-etch adhesive system to ... See full document

... self-adhesive resin cements have recently introduced to simplify the procedure for ...cementing. The objective of this study is to evaluate the effectiveness of ... See full document

... Self-adhesive resin cements do not require prior preparation of the tooth surface, therefore dentin pretreatments may influence long-term bond ...evaluate the ... See full document

... evaluate the bond strength between human dentin and composites, using two light-activated single-bottle total-etch adhesive systems with different pHs combined with ... See full document

... aim of this in vitro study was to evaluate the effect of epigallocatechin-3-gallate (EGCG) on resin-dentin bond strength in the periods immediately ... See full document

... evaluated the tensile bond strength of glass fiber posts (Reforpost – Angelus-Brazil) cemented to root dentin with a resin cement (RelyX ARC – 3M/ESPE) associated with two ... See full document

... examined the effect of deproteinization on the microtensile bond strength between conventional and self-adhesive resin cement and dentin ... See full document

... concept of adhesion to dentin relies on the infiltration of monomers from the adhesive resin within the etched dentin tissue (collagen mesh), in order to ... See full document

... Switzerland) and L accessory gutta-percha cones (Dentsply Sirona, Ballaigues, Switzerland) with AH Plus or EndoREZ ...sealers. The base and catalyst pastes for the AH Plus sealer were ... See full document

... Conclusion: Epiphany sealer presented higher bond strength values to dentin in both irrigating protocols, and the use of 2.5% NaOCl and 17% EDTA increased the bond strength values for [r] ... See full document

... Flat dentin surfaces from 36 primary molars were assigned to three groups (n = 12) according to method to induce caries-affected dentin: (1) control (sound dentin); (2) pH-cycling; and (3) ... See full document

... Etch-and-rinse resin cement (Single Bond/RelyX ARC; 3M ESPE, St Louis, USA) – Intracanal dentin was etched with 37% phosphoric acid for 15 seconds, rinsed with distilled water for 15 seconds, ... See full document

... Dentin is a dynamic substrate,i'' and its morpho- iogicai and functional characteristics are determi- nants of the quality of resin-dentin bonds achieved with adhesive agents.^° Scleroti[r] ... See full document