[PDF] Top 20 MAT (Micro Agglutination Technique): MAT was performed in all

... µm in diameter, not usually seen in stained smears, but observed alive with active motility through dark-field ...days in liquid ...available in routine medical microbiology ... See full document

... extrusion was performed on the vulcanized elastomers pursuing selectively crosslink rupture and the same characterization previously cited was conducted on the devulcanized material, except the ... See full document

... biodegradation in soil, by the mass loss and the mechanical properties of plastic ...biodegradation in soil. Based on the results, it was observed that all the studied tubes lost mass over the ... See full document

... enrolled in this study from the pulmonology outpatient clinic at our facility. All patients were ...assessed in detail and pulmonary function tests were performed in a standard fashion ... See full document

... reported in literature was performed, as shown in Table ...values in Table 3 were obtained under several diferent experimental conditions and, therefore, the maximum capacity (q m ) ... See full document

... impact. In Fig. 6, it was revealed the typical appearance of MASs after ballistic ...test. In this igure, one should notice that in all MASs the front ceramic was totally ... See full document

... In this work, physical, chemical and morphological modiications of three diferent polyamide 6.6 (PA6.6) fabrics were investigated using double barrier dielectric (DBD) plasma treatment. Several techniques of ... See full document

... technique in the pelvic floor muscle activity, noting the type of fiber was more work during the practice of this activities in soil (Mat ...It was a character study of interventional, ... See full document

... diference in nickel content and the tempering temperatures on the corrosion resistance in ...There was passive ilm formation and pitting corrosion in all tempering temperatures of the ... See full document

... It was discovered that all concretes produced met the minimum strength of 20 MPa recommended by NBR 6118 for structural purposes, and it was observed an increase of the compressive strength on the ... See full document

... measurements in a Vibrating Sample Magnetometer (VSM) were performed to detect and quantify austenite in the various heat treatment ...) was determined by extrapolation of the magnetization x ... See full document

... steel was a 3-mm thick hot-rolled ...material was used as the base ...used in the GTAW ...reported in Table 2. The weld was performed toward the perpendicular direction to the ... See full document

... to its structure the cassava starch is highly hydrophilic and therefore has low ainity with natural BT clay. An intercalated nanocomposite is formed where the stacked clay structure does not completely interact with the ... See full document

... powder (mean particle size of 5.65µm) and 10%wt. commercial Co powder (particle size below 53µm). The second alloy, named REC, was prepared with a WC-Co powder produced by milling of hard metal scrap. The particle ... See full document

... attention in the past years as an advanced material due to its combination of desirable properties: high mechanical strength, high thermal and chemical stability, low sintering temperature, low surface acidity, ... See full document

... molding in a DIPAMAK (Model 30T) hydraulic ...mixture was set to cure at room temperature for 24 h inside a 152 x 122 x 10 mm rectangular mold under ...standard, in an Instron machine (Model 5582) ... See full document

... it was observed that the indented areas corresponded to free points of pull-out, which is conirmed that it did not signiicantly interfere in the hardness ...test. In both methods there was ... See full document

... Cu in particles form which results in high sinterability and densiication of W-30 wt% Cu ...powder was obtained by manually mixing the APT and copper nitrate and reducing under a hydrogen atmosphere ... See full document

... may in this case be by mechanical impediment (thermal stability of the alumina) and/or by dissolution of the latter in the glass forming crystalline phases (such as lithium aluminum silicates) more ... See full document

... cracks in the surface start to propagate, and the plastic deformation will concentrate in this ...showed in Figure 4 by MAR-SAP sample indicates the higher roughness of the nitrided layer and may ... See full document