[PDF] Top 20 Effect of chlorhexidine incorporation on the surface properties of acrylic reline resins

... a reline resin with 5% or 10% w/w of CHX incorporated among other antimicrobials, concluding that the incorporation of CHX didn’t affect the shear bond values, as the ... See full document

... In the present study, there were no statistical differences found between Kooliner experimental groups and the ...studied the shear bond strength of Kooliner specimens immediately after ... See full document

... feasibility of introducing antimicrobial and antifungal agents in acrylic resins or soft liners acting as drug carriers for the treatment of denture induced stomatitis has been ... See full document

... 9 The 150 denture base specimens were randomly divided into three groups, corresponding to the three different acrylic reline ...area of 3 mm in diameter, a perforated adhesive tape ... See full document

... purpose of this study was to evaluate mass variation color stability and drug release of acrylic reline resins loaded with chlorhexidine after thermal ...in the present ... See full document

... of the polymer chain may account for the relatively lower hardness of Tokuso Rebase Fast in comparison to Ufi Gel Hard ...that the greater surface hardness of Ufi Gel Hard ... See full document

... base acrylic resins have polymethylmethacrylate in their ...discussed the polymerization process involved in converting monomer into polymer because adequate polymerization is a crucial factor in ... See full document

... (PMMA) resins have commonly been used as a denture base ...that the 2-tert- butylaminoethyl methacrylate (TBAeMA) incorporated to acrylic resins should have antimicrobial activity related to ... See full document

... Kooliner reline resin, five CHX concentrations were studied, 1%, ...During the ageing procedure, 8 specimens per group of CHX concentration, with ...cycles of thermal fluctuations between 5°C ... See full document

... total of thirty-six specimens of heat-polymerizing denture base acrylic resin Probase Hot (Ivoclar Vivadent AG, Liechtenstein) (Appendix 2, Figure 14) were ...all the wax specimens obtained ... See full document

... Firstly, the specimen’s dimensions (height, width and thickness) were measured using a digital micrometer (Mitutoyo Digimatic, ...in the software just before testing. At the beginning of each ... See full document

... use on resin acrylics (Addy ...number of microorganisms, where Candida is ...both on releasing and microbiological tests (Lamfon et ...evaluated the effect of CHX ... See full document

... to the microhardness test and the use of the Knoop indenter tool for the measurements, it can be stated that the Knoop hardness number (KHN) is determined by the length ... See full document

... samples of whey cheese, taken at 0, 7 and 21 d of storage, were assayed for organic acids and sugars; these sampling times were chosen based on preliminary evidence on the expected time ... See full document

... [20,23]. The different microalgae biochemical compositions can affect physical and sensorial aspects of the biomass [20,23] and of microalgae-based products such as for food gels, cookies, ... See full document

... examined the average surface roughness (Ra, µm) of 2 microfilled (Durafill and Perfection), 1 hybrid (Filtek Z250) and 2 packable composite resins (Surefil and Fill Magic), before (baseline) ... See full document

... consists on a set of equipment (Figure 2), starting at the microwave oven itself (Brastemp DES 950W/12,7A, Multibras Eletro- domesticos ...Inside the oven, the specimens were always ... See full document

... selection of a finishing instrument depends on the nature of the restorative material, localization, and size of a given ...discs of aluminum oxide, but their application ... See full document

... Foi constatado, ainda, que os resultados encontrados pela sorção de AM em XRF empregando tanto refluxo como ultrassom diferem dos resultados encontrados pela análise de CTC pelo método[r] ... See full document

... Alexiou PN, Marchant JF, Groves KW. Effect of pre- steaming on moisture gradients, drying stresses and sets, and face checking in regrowth Eucalyptus pilularis Sm. Wood Science and Technology 1990; ... See full document