[PDF] Top 20 Effect of thermal treatment on flexural strength of bis-acrylic resin

... Regardless of being used for a limited period of time, these restorations must comprise certain requirements to resist functional and non-functional ...appraisal of the patient’s oral health and ... See full document

... the effect of 16% carbamide peroxide (Whiteness Perfect/FGM) on the Vickers microhardness and flexural strength of the restorative composites Filtek Z100 (hybrid), Filtek Z350 ... See full document

... use of effervescent tablets is recommended to clean intra- and extra-oral acrylic resin prostheses (Goiato et ...decomposition of polymerized chemically-activated acrylic resin ... See full document

... bond strength values when compared to the control ...study of Barreiros (2015), which means that even with thermal ageing (that is expected to promote an additional polymerization of the ... See full document

... the bis-acrylic resin (Protemp 4, P4; Structur 3, S3) and post-polymerization thermal treatment (without any post-polymerization treatment, nt; post-polymerization in a water ... See full document

... the effect of denture base polymer type (heat- and microwave-polymerized), ridge lap surface treatment (with and without methyl methacrylate-MMA etching) and thermocycling on the microtensile ... See full document

... period of time than ...exposure of zirconia in the oral environment could be expected such as the common clinical problem, chipping of the veneering ceramic from zirconia framework that may also ... See full document

... the flexural strength of the materials were compared, Lucitone 550 (short cycle) exhibited significantly higher flexural strength than Ufi Gel Hard C and Lucitone 550 (long cycle) in ... See full document

... bond strength is dependent on the chemical composition of both materials, defended previously by others authors (Arima et ...Bonding of autopolymerizing resins to denture base resin ... See full document

... feasibility of introducing antimicrobial and antifungal agents in acrylic resins or soft liners acting as drug carriers for the treatment of denture induced stomatitis has been investigated by ... See full document

... incorporation of TBAeMA in products for dental ...heat-polymerized acrylic resin (Lucitone 550) was ...incorporation of TBAeMA in another acrylic resin with different ... See full document

... methods of specimen preparation were used to obtain smooth and rough surfaces that simulate the outer and inner surfaces of the dentures, ...layer of separating medium (Vipi Film; VIPI Indu´ stria e ... See full document

... completion of the surface treatment described above, µSBS test was ...USA) on treated zirconia surface, delimited by an adhesive tape ...irradiance of 500 mW/ cm 2 , verified by the radiometer ... See full document

... form of gels and containing varying concentrations of hydrogen peroxide combined with few other substances like stabilizers, catalysts and flavor agents ...influence of those additional substances ... See full document

... a thermal ageing of the specimens, more experimental studies are needed to conclude about the biodegradation of acrylic reline resins exposed to the oral ...biodegradation of a ... See full document

... purpose of this study was to investigate the dimensio- nal stability of denture bases influenced by Clássico acrylic resin stages, proportioned according to manufacturer’s ins- ...groups ... See full document

... development of other forms of candidosis when submitted to conditions that might lead to a disequilibrium in the oral microbiota, such as us- age of broad-spectrum antibiotics, anti-histamines, ... See full document

... respect of study limitations the size of the specimens used in this in vitro study is very different from the denture ...number of surfaces releasing chlorhexidine in the cylinders while in the ... See full document

... use of this wood has caused many frustrations in the timber industry due to the sawn and drying defects, leading to considerable loss of raw materials and consequent economic losses, as well as other ... See full document

... stream of warm air (45 ± 5 °C) generated from a blow dryer (model RV456ABG; Revlon, El Paso, TX, USA) for 15 s to approximately 15 cm from the ...coats of adhesive, air-drying for 10 s at 20 cm and ... See full document