[PDF] Top 20 J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
Has 10000 "J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3" found on our website. Below are the top 20 most common "J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3".
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... The proposed method is based in the Moving Least Square Approximation (MLSA) and is capable of overcoming singularity problems, in the global shape functions, resulting from the consid[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... The methodology for calculating the flow with separation in aerodynamic bodies, including the viscous effects, is based on two computational codes 1) The potential[r] ... See full document
12
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... Pressure curves in the interior of the combustion chamber as a result of the crankshaft angle and the percentage of recirculation for a 3000 rpm for the naturally aspirated engine wit[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... Vivès,C., 1989, “Electromagnetic refining of aluminum alloys by the CERM process: part working principle and metallurgical results”. Metallurgical Transactions, Vol. 20b, pp.623-629. and Viv è s,C., 1989, ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... The objective of this study was to evaluate some geometrical and loading conditions that might interfere in the stress concentration of specimens submitted to microtensile bond streng[r] ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... In this article the invariance of the Novozhilov's mean rotation measures will be emphasize by the invariance of the determinant of the gradient of deformation tensor of continuum mech[r] ... See full document
3
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... As one may observe from experimental Deformation- Temperature curves (under constant loads), the greater the prescribed strain, the higher the load under which the phase transformation[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... Keywords: structural engineering, semi-rigid joints, steel structures, neural networks, semi-rigid behaviour, flexural resistance and joint stiffness.. Introduction1[r] ... See full document
11
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... Considering the reduced number of studies evaluating the influence of specimen dimensions on contraction stress development, as well as the discrepancies found among authors regarding[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... Figures 2 and 3 show pressure contours obtained by both Jameson and Mavriplis explicit scheme (1986) and Frink, Parikh and Pirzadeh explicit scheme (1991), respectively.. A CFL number [r] ... See full document
13
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... The temperature in the soot- formation region is determined by first establishing the temperature of the rich reaction products and how they are affected by the diffusion flame and pre[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... (step b) is taken as an estimate of the current velocity of the struc- ture. This velocity is computed by a simple linear extrapolation from the structural velocity and acceleration computed at the previous time step. As ... See full document
11
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... resin transfer molding (RTM), resin film infusion (RFI), and hand lay-up, the problem of void formation is also related to the manufacturing process parameters such as fiber volume fr[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... Calculations show that the stagnation point heating on power law leading edges with finite radius of curvature follows the same relation for classical blunt body in continuum flow; it [r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... In the present work, the least- squares finite element method (LSFEM), Jiang (1998), has been implemented for simulation of laminar, transitional and turbulent fluid flows using veloci[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número1
... Results obtained with microthermocouples (Hohl and Auracher, 2000; Hohl, 1999) let us furthermore assume that at wall superheats beyond CHF the two-phase structure at a given wall supe[r] ... See full document
22
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Figure 13 shows this generated irregular wave pattern (input) and the performance of (a) an anchored platform and platforms equipped with three different DPS controllers: (b) PID[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número1
... perimeter wetted by the axial flow of liquid film, which refers to the entire perimeter in annular, intermittent and mist flows but only part of the perimeter in stratified-wavy a[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... In the equation, the diffusion coefficient depends whether the considered region is the liquid, interface or solid. The system of equations resulting from the integration of the differential equations is solved by the ... See full document
13
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... Transmission loss of a simple expansion chamber using an extended tube length of 0.1 mm; TMM results (dashed line) and experimental results (solid line).. Figure 6 shows comparisons fo[r] ... See full document
9
temas relacionados