Removal rate
Optimization of Material Removal Rate in Cnc Turning of Mild Steel 1018 Using Taguchi Method
... This study demonstrates that, when feasible process parameters are selected, mild steel (1018) could be efficiently turned using coated carbide tool. The coated carbide tool with better mechanical and thermal properties ...
5
Experimental Analysis of Material Removal Rate in Drilling of 41Cr4 by a Taguchi’s Approach
... In manufacturing industries the largest amount of money spent on drills. Therefore, from the viewpoint of cost and productivity, modeling and optimization of drilling processes parameter are extremely important for the ...
6
Studies on the Material Removal Rate of Al-SiC Composites Machined by Powder- Mixed EDM Technique
... The plot for changes in MRR for variations in peak current for different pulse-on times at 9%wt. SiC concentration in Al matrix is shown in figure 4. It can be noted from the plot that for any given value of pulse on ...
8
Prediction of Material removal rate for Aluminum BIS-24345 Alloy in wire-cut EDM
... x3 7 ) orthogonal array. Each experiment was conducted under different conditions of pulse on time, pulse off time, peak current, flushing pressure of dielectric fluid, wire feed rate, wire tension, spark gap ...
11
Effect of Electric Discharge Machining on Material Removal Rate and White Layer Composition
... cooling rate in EDM is also associated with the refined grain structure as compared to grinding and turning process ...material removal rate of aerospace grade (2024 T6) aluminum alloys has been ...
10
J. Braz. Soc. Mech. Sci. & Eng. vol.32 número especial a09v32nspe
... At present, due to their properties, the tungsten carbide-cobalt (WC-Co) composite materials are in huge demand by industry to manufacture special tools, dies/molds and components under erosion. The powder metallurgy is ...
7
Prediction of Electrochemical Machining Process Parameters using Artificial Neural Networks
... In this study two different algorithms were tried for adjusting network weights in order to reduce the output error. At first training was conducted using gradient decent with momentum and then, levenberg marquardt was ...
8
BRAZILIAN ARCHIVES OF BIOLOGY AND TECHNOLOGY
... glucose removal rate in response to insulin, was probably related to the increase in sensitivity to the hormone in the intact skeletal muscle, as suggested by the results of glucose uptake by the isolated ...
8
Review on "automation in fruit harvesting"
... An early limb shaker was represented by Coppock and Jutras using inertia developed by Adrain and Fridley. An eccentric weight about 85 pounds was rotated in the mechanism to produce the shaking action after the shaker ...
15
J. Braz. Soc. Mech. Sci. & Eng. vol.30 número3
... wear rate in ultrasonic drilling of engineering ...material removal rate (MRR) and tool wear rate in ultrasonic machining of titanium ...feed rate and ultrasonic power) were considered ...
8
REVIEW PAPERS IDENTIFICATION, ASSESSMENT AND ORDERING OF CONCEPTS FOR AGRO-ENERGY PLANNING AND POSSIBILITIES OF SPATIAL ANALYSIS
... sugarcane straw section (e.g. sugarcane to straw ratio, straw removal rate). Yet, it should be pointed out that, associated with the information of sugarcane spati[r] ...
14
EXPERIMENTAL INVESTIGATIONS ON MRR AND SURFACE ROUGHNESS OF EN 19 & SS 420 STEELS IN WIREEDM USING TAGUCHI METHOD
... Quality and sophistication of the parts / products are the main requirements of the customer in the present global market. Therefore, the manufacturing / Production industries are searching for un-conventional machining ...
12
Investigating the Effect of Copper Chromium and Aluminum Electrodes on EN-31 Die Steel on Electric Discharge Machine Using Positive Polarity
... material removal rate (MRR) and SR which affects machined work piece and hence tool ...metal removal rate, better surface finish and greater dimensional accuracy, with less tool ...
5
Experimental Study on Parametric Optimization of Titanium based Alloy (Ti-6Al-4V) in Electrochemical Machining Process
... Material Removal Rate (MRR) are of extremely important in ECM Use of optimal ECM process parameters can significantly reduce the ECM operating, tooling, and maintenance cost and will produce components of ...
5
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... material removal is assured by direct hammering and impact action of the abrasive particles against the surface of the workpiece (Shawn, 1956; Kainth et ...material removal and particle crushing, may ...
6
EXPERIMENTAL INVESTIGATION ON ELECTRICAL DISCHARGE MACHINING OF TITANIUM ALLOY USING COPPER, BRASS AND ALUMINUM ELECTRODES
... Since, EDM is thermal erosion process, the amount of material removal or material removal rate should be a function of melting point of the workpiece material. Also, the heat generated from the arc ...
9
Experimental Investigation of Effect of Process Parameters on Mrr and Surface Roughness In Turning Operation on Conventional Lathe Machine For Aluminum 6082 Grade Material Using Taguchi Method
... In a global competitive environment every industries are trying to decrease the cutting cost and increased the quality of machined parts/components. So, it required to focus on material removal rate and ...
9
Kinetics and thermodynamic properties related to the drying of ‘Cabacinha’ pepper fruits Hellismar W. da Silva
... water removal rate, effective diffusion coefficient and Gibbs free energy, besides a reduction in fruit drying time and in the values of entropy and ...
7
Electrochemical treatment of leachates from sanitary landfills
... flow rate on the performance of the electrochemical oxidation was ...flow rate and initial current intensity, chemical oxygen demand (COD) removal seems to depend mainly on the charge passed and the ...
11
CWS2 isolated from polycyclic aromatic hydrocarbon-contaminated soil
... C. cellulans CWS2 was isolated from PAH-contaminated soil in a coking plant. The strain uses BaP as the sole carbon and energy source under nitrate-reducing conditions. Tempera- ture and pH of the broth were the main ...
11