Titanium alloy
Hot deformation behavior of TC18 titanium alloy
... TC18 titanium alloy at the deformation tempera- tures ranging from 25 °C to 800 °C and strain rate ranging from 10 –4 to 10 –2 s –1 were conducted by using a WDW-300 electronic universal testing ...
6
The treatment effect of porous titanium alloy rod on the early stage talar osteonecrosis of sheep.
... porous titanium alloy rod (IM group) achieved a better therapeutic outcome than the traditional core decompression treatment (DC group), especially in terms of bone tissue regeneration and ...
9
Effects of low-dose microwave on healing of fractures with titanium alloy internal fixation: an experimental study in a rabbit model.
... with titanium alloy can’t cause irreversible damages to the muscle around the ...the titanium alloy implants were ...the titanium alloy (Figure ...
10
EXPERIMENTAL INVESTIGATION ON ELECTRICAL DISCHARGE MACHINING OF TITANIUM ALLOY USING COPPER, BRASS AND ALUMINUM ELECTRODES
... have worked on optimization for EDM process parameters with multiple performance characteristics. Electrical Discharge Machining is achieved by applying a succession of discrete discharge between electrode (cathode) and ...
9
Effect of CVD-Diamond on the Tribological and Mechanical Performance of Titanium Alloy (Ti6Al4V)
... A comparison has been documented between nanocrystalline diamond (NCD) and microcrystalline diamond (MCD) coatings on titanium alloy (Ti6Al4V) substrates with architectures of Ti6Al4V/NCD and Ti6Al4V/MCD, ...
13
Fibroblast and pre-osteoblast cell adhesive behavior on titanium alloy coated with diamond film
... together inside the deposition chamber beside the titanium alloy samples only for comparative analysis, since silicon substrate is largely used when diamond film is studied. All of them were treated in a ...
7
Corrosion and cell viability studies of graphite-like hydrogenated amorphous carbon films deposited on bare and nitrided titanium alloy
... the titanium alloy or other substrates preventing health problems like toxicity, allergic response and car- cinogenic reactions depending on the ion ...
7
Characterizing the Effect of Processing Parameters on the Porosity of Laser Deposited Titanium Alloy Powder
... of titanium medical implants because titanium is a difficult to machine material using traditional manufacturing methods such as milling and ...turning. Titanium and its alloys are more difficult to ...
5
Corrosion, wear and wear –corrosion behavior of graphite-like a-C:H films deposited on bare and nitrided titanium alloy
... bare alloy showed a wide range of rubbing distances until failure that can be asso- ciated to the probability of occurrence of defects on the wear track or near it (close enough to suffer the adverse effect of ...
7
SURFACE FINISH WHEN THREADING TITANIUM-BASED ALLOY UNDER DRY MACHINING
... that titanium alloys have poor machinability due to generation of a high cutting temperature, short chip tool contact length and low elastic ...of titanium alloy, very high cutting temperatures are ...
8
Multiaxial fatigue strength of severely notched titanium grade 5 alloy
... the titanium alloy Ti-6Al-4V a different size of the control volume under tension and under torsion, due to a very different notch sensitivity for tension and ...
9
Analysis of surface roughness and cutting force during turning of Ti6Al4V ELI in dry environment
... machining titanium alloys at the speed range of 185–220 ...of titanium alloy Ti-6Al-4V ELI by using PVD TiAlN insert in turning process under dry ...
10
Influence of Si Coating on Interfacial Microstructure of Laser Joining of Titanium and Aluminium Alloys
... aluminium alloy exhibits a fine cellular dendritic solidification structure with many equiaxial grains in the weld centerline (Figure ...of titanium alloy side. While the titanium alloy ...
8
C Metal Matrix Composites using Laser Treatment
... Moreover, titanium alloys can be boronised efficiently to increase hardness and wear ...Ti6Al4V alloy powder for LMD process has been ...Ti6Al4V alloy brings about an increase in hardness of surface ...
10
Powder Flow Rate Influence on Laser Metal Deposited TiC on Ti-6Al-4V
... methods. Titanium and its alloys are one of the difficult materials to machine since they cause galling on the cutting ...on Titanium alloy grade 5 and the effect of varying the powder flow rate on ...
5
Chemical analysis and Vickers hardness of orthodontic mini-implants
... the titanium alloy (Ti-6Al-4V) chosen for manufacture of mini-implants incorporates aluminum (Al) and vanadium (V) into its composition along with commercially pure titanium (cpTi) 10 ...
4
Braz. Dent. J. vol.21 número6
... pure titanium (CP Ti - G1), cobalt-chromium alloy (Co-Cr - G2) and nickel-chromium-titanium alloy (Ni-Cr-Ti - ...Co-Cr alloy presented the worst values for passive ...
5
Mat. Res. vol.7 número2
... The titanium substrate usually investigated in the literature is subjected to an alkali treatment to induce the calcium phosphate formation and improve adhesion of the ...substrates titanium alloy ...
6
Experimental Study on Machinability of Ti-6Al-4V in Micro End-Milling
... ITANIUM alloy has been an attractive material for aerospace and biomedical industries because of their superb mechanical property, high strength-to-weight ratio, corrosion resistance, and ...However, ...
5
Dental Press J. Orthod. vol.15 número1
... beta-titanium alloy on its ...beta-titanium alloy kept them statistically related to the lowest tipping numerical values observed for the retracted dental ...
12