Titanium alloy (Ti6Al4V)
Effect of CVD-Diamond on the Tribological and Mechanical Performance of Titanium Alloy (Ti6Al4V)
... A comparison has been documented between nanocrystalline diamond (NCD) and microcrystalline diamond (MCD) coatings on titanium alloy (Ti6Al4V) substrates with architectures of Ti6Al4V/NCD and Ti6Al4V/MCD, ...
13
Characterizing the Effect of Processing Parameters on the Porosity of Laser Deposited Titanium Alloy Powder
... Abstract— Laser Metal Deposition (LMD) is an additive manufacturing technique that produces parts layer by layer directly from the Computer Aided Design (CAD) file. Highly customized parts with complex shapes such as ...
5
The treatment effect of porous titanium alloy rod on the early stage talar osteonecrosis of sheep.
... porous titanium alloy rods were prepared and implanted into the tali of sheep with early-stage ONT (IM ...porous titanium alloy rods into the tali of sheep with early-stage ONT may provide ...
9
Effects of low-dose microwave on healing of fractures with titanium alloy internal fixation: an experimental study in a rabbit model.
... steel, titanium alloy is a kind of medical implants with low magnetic permeability and electric ...of titanium alloy implants and phantom in vitro ...by titanium alloy are non- ...
10
Fibroblast and pre-osteoblast cell adhesive behavior on titanium alloy coated with diamond film
... The region marked as “1” in Fig. 1 shows that the early growth of the film does not form homogeneous interface. Probably due nucleation spots created during seeding procedure described here in the 2.1 material and ...
7
EXPERIMENTAL INVESTIGATION ON ELECTRICAL DISCHARGE MACHINING OF TITANIUM ALLOY USING COPPER, BRASS AND ALUMINUM ELECTRODES
... have worked on optimization for EDM process parameters with multiple performance characteristics. Electrical Discharge Machining is achieved by applying a succession of discrete discharge between electrode (cathode) and ...
9
Hot deformation behavior of TC18 titanium alloy
... example, titanium alloys were widely used in military domain because of its good adiabatic shear properties, the application of aerospace field were mainly due to its high specific ...(BT22) titanium ...
6
Corrosion and cell viability studies of graphite-like hydrogenated amorphous carbon films deposited on bare and nitrided titanium alloy
... the titanium alloy or other substrates preventing health problems like toxicity, allergic response and car- cinogenic reactions depending on the ion ...
7
Corrosion, wear and wear –corrosion behavior of graphite-like a-C:H films deposited on bare and nitrided titanium alloy
... nitrided alloy presented a lifetime at least ten times shorter than that of films on bare ...GLCH/nitrided alloy interaction facilitates fluid penetration between the film and the substrate which leads to a ...
7
Mat. Res. vol.7 número2
... Titanium alloy Ti6AL4V ASTM F136 (Ti) and stainless steel AISI 316L (SS) plates were cut into small rectangular samples (20 mm, 10 mm, 1 ...on titanium 6 ...
6
Analysis of surface roughness and cutting force during turning of Ti6Al4V ELI in dry environment
... Haron et al. (2011) found that the feed was the most dominant factor influencing the surface roughness. Acceptable surface roughness achieved when cutting speed was 160 m/min; feed was 0.18 mm/rev and depth of cut was 1 ...
10
C Metal Matrix Composites using Laser Treatment
... Moreover, titanium alloys can be boronised efficiently to increase hardness and wear ...Ti6Al4V alloy powder for LMD process has been ...Ti6Al4V alloy brings about an increase in hardness of surface ...
10
Multiaxial fatigue strength of severely notched titanium grade 5 alloy
... he material under investigation is a grade 5 titanium alloy, also known as Ti-6Al-4V. The geometries of the un- notched and V-notched specimens are shown in Fig. 1 together with some details of the notch ...
9
Braz. Dent. J. vol.21 número6
... pure titanium (CP Ti - G1), cobalt-chromium alloy (Co-Cr - G2) and nickel-chromium-titanium alloy (Ni-Cr-Ti - ...Co-Cr alloy presented the worst values for passive ...
5
Chemical analysis and Vickers hardness of orthodontic mini-implants
... the titanium alloy (Ti-6Al-4V) chosen for manufacture of mini-implants incorporates aluminum (Al) and vanadium (V) into its composition along with commercially pure titanium (cpTi) 10 ...
4
Powder Flow Rate Influence on Laser Metal Deposited TiC on Ti-6Al-4V
... methods. Titanium and its alloys are one of the difficult materials to machine since they cause galling on the cutting ...on Titanium alloy grade 5 and the effect of varying the powder flow rate on ...
5
SURFACE FINISH WHEN THREADING TITANIUM-BASED ALLOY UNDER DRY MACHINING
... Visual optical observation on specimens produced by the worn tool revealed several types of surface texture damage, as shown in Figure 5 and Figure 6. Machining of the titanium alloy with the nearly worn ...
8
Braz. Dent. J. vol.22 número1
... gold alloy prosthetic screws increased after 5 or 10 tightening ...over titanium alloy screws, about 10 Ncm, these screws present values of daily preload approximately 10% higher when compared to ...
5
Influence of Si Coating on Interfacial Microstructure of Laser Joining of Titanium and Aluminium Alloys
... between titanium and aluminium ...of titanium and aluminium alloys have been carried out using a Yb:fiber laser, considering the prior silicon film deposited on titanium alloy interface by DC ...
8
Experimental Study on Machinability of Ti-6Al-4V in Micro End-Milling
... The above-mentioned problems can be more significant in micro-scale machining of difficult-to-machine materials. However, a limited number of researches on micro-scale machining of difficult-to-machine materials have ...
5