[PDF] Top 20 J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
Has 10000 "J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1" found on our website. Below are the top 20 most common "J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1".
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... The benefits of high pressure coolant supply seem more obvious when machining commercially available titanium, Ti6Al4V, alloy (IMI 318) with coated and uncoated carbide tools as well as with Polycrystalline Diamond (PCD) ... See full document
11
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... For the weld metals in the normalized condition, Fig. 5 shows that Charpy V energy at -20°C is higher for the CMn weld metal, followed by CMnMo, CMnMoTiB and CMnMoCr. The last two weld metals present results below the ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... The following are the corrections in the paper entitled " Analysis of a Porous Exponential Slider Bearing Lubricated with a Ferrofluid Considering Slip Velocity by Rajesh C.Shah a[r] ... See full document
1
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... J. of the Braz. Soc. of Mech. Sci. & Eng. Copyright © 2004 by ABCM January-March 2004, Vol. XXVI, No. 1 / 103 The micrographies presented in Figs. 4a’, 4b’, 4e’ and ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... Thread milling tools (a) Single cutting edge, (b) Single straight thread flute, (c) Helical thread flute (Emuge, 2002).. Many authors developed models for prediction of forces in mach[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... The following two sections are indispensable for reader comprehension and were summarised from Altintas (2000). Consider a milling cutter with two degrees of freedom and N number of teeth with a zero helix angle as shown ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... In order to define information structures that capture not only the information related to the product life cycle, but also, the information and knowledge associated to the different p[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... 1) For many pipeline applications, mechanised GMAW is still considered the most suitable process. The use of dual-torch welding bugs has reduced construction costs and further reducti[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... Material removal rate, surface finish and machining accuracy are influenced by various operational parameters such as amplitude and frequency of ultrasonic oscillations, static load a[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... Samples cut from tensile test specimens in the tension axis direction were used for dilatometry tests, performed in an Adamel Lhomargy LK02 equipment, in the temperature range from 25[r] ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... Using rapid molds, pre-series of parts are obtained in record time with the injection molding material chosen to manufacture the final parts.. So, tests may be extended to a wide rang[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... The proposed modified Fowler-Milne method, based on a linear distribution of the particle density instead of a Maxwellian one, at temperature below 10,000 K, showed very useful for cal[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... The problem was to choose the near-best values of three control variables (welding voltage, wire feed rate and welding speed) based on four quality responses (deposition efficiency, be[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... Those tests were essentially aimed to the comparison of the material presently used for engine blocks, cast iron FC-250, with the compacted graphite iron class CGI-550.. Both materials[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... This Ra value shows that the radial depth of cut, feed per tooth and tool overhang used in this work are suitable for reaching surface roughness values good enough to obtain a kind of[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... This innovate mapping system is being used in grinding process to detect inefficient dressing cycles, unbalancing and vibrations detection, non-uniform interaction between wheel and w[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número1
... machining with alumina base nano-ceramic tools T1 and T2. This shows that the tools maintain their hardness at higher speed conditions. Cutting forces generated when machining with the[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número4
... It is discussed: the optimal placement of actuators, the model reduction and the controller design through techniques involving linear matrix inequalities (LMI).. It is considered as c[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número4
... Evaluation of Subsurface Contact Stresses in Railroad Wheels Using an Elastic Half-Space Model.. Railroad wheels fail in two main modes: rolling surface defects like spalling, shelling[r] ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.26 número3
... However, those research works consider that the necessary information for the analysis (e.g. the contacts among the parts in the assembly) is already available, which is not[r] ... See full document
11
temas relacionados