Maximum load
Análise comparativa entre o valor de carga máxima e carga de fissuração em um CRFA / Comparative analysis between the maximum load value and cracking load in a CRFA
... this load capacity only happens if the concrete is used properly and, for this, there are reference codes that establish design aspects for the use of the ...the maximum load corresponds to the ...
21
Rapid-throughput skeletal phenotyping of 100 knockout mice identifies 9 new genes that determine bone strength.
... testing load frame (Instron Limited, High Wycombe, Buckin- ghamshire, UK) using custom built mounts with rounded supports that minimize cutting and shear loads ...upward. Load was applied vertically to the ...
14
Rev Bras Med Esporte vol.10 número6 en a07v10n6
... the maximum load (ML) in leg flexion and extension and elbow flexion alone and between the sum of these two results with that developed simultaneously by both legs and arms, ...lower load increment – ...
4
Braz. J. Phys. Ther. vol.18 número3
... The assessment was performed by a cardiologist to determine the maximum load the patients were able to achieve. In addition, this step was considered important to assess the clinical and functional ...
10
Effect of the Distance Between Impact Point and Hole Position and Non-Perpendicular Holes on the Impact Strength of Composite Laminates
... the maximum and minimum values obtained from the five ...average maximum load of 1535 N was found, and this value tends to decrease with the angle of the ...average maximum load ...
6
Mat. Res. vol.18 número1
... In view of their numerous advantages, natural iber reinforced composites have been considered as potential candidates for structural applications, such as low cost residential compounds in developing countries. ...
7
Identification of equipment and procedures used by Brazilian physical therapists for inspiratory muscle endurance tests
... incremental load exercise a fixed charge of 30% of the MIP was used with increment of 10% every two ...of maximum load a fixed charge of 70% of MIP was used and the time limit reached until ...
9
Matéria (Rio J.) vol.15 número2
... the maximum load for break and tensile strength improved with the incorporation of coir fibers into both the starches, which increased with increasing fiber content, while % elongation decreased ...
8
Mechanical evaluation of bone gap filled with rigid formulations castor oil polyurethane and chitosan in horses
... the load to be employed; the first was submitted to destructive testing for elastic limit determination while the second was submitted to repeated non-destructive compression to evaluate potential changes between ...
7
Lat. Am. j. solids struct. vol.13 número5
... a load cell with a max capacity of 30 kN. The test consisted on a load application to the specimen in a longitudinal direction until failure, with a constant displacement rate of 1 mm/min (quasi-static) and ...
19
Rev Bras Med Esporte vol.12 número6 en a12v12n6
... tolerated maximum load) ...the maximum load test. Before the maximum load test, except for the group CRE-NAT (3-5 w eeks), that present- ed low er level of plasma glucose ...
5
ENSAIO MECÂNICO PRELIMINAR DO REFORÇO FEMORAL PROXIMAL COM CIMENTO ÓSSEO EM FORMA DE “X”
... for maximum load and absorbed energy obtained in this study cannot be compared to the results found in the literature, as the mechanical properties of the model are far beyond those of the cadaver models ...
5
Lat. Am. j. solids struct. vol.13 número12
... 3PB load and the normalised mechanical load during each ...applied load reaches approximately the level of the maximum load of the previous loading ...a maximum of approximate- ...
15
Static Analysis of G+2 Institutional Building in Bhopal
... Salehuddun (2011) focused on nonlinear geometric analysis to be compared with linear analysis. In this study, a six storey 2-D steel frame structure with 24 m height has been selected to be idealized as tall building ...
9
Steady State Thermo-Hydrodynamic Analysis of Two-Axial groove and Multilobe Hydrodynamic Bearings
... number, load carrying capacity decreases. With increase in groove angle ( ) load capacity decreases ...region. Load capacity decreases with increase in temperature-viscosity coefficient, as viscosity ...
13
Rev. bras. ortop. vol.52 número5
... Most stress fractures occur in the lower limbs and are rarely observed in the upper limbs. The second metacarpal is the longest of all the metacarpals and has the largest base, articulating with the trapezium, trapezoid, ...
4
Experimental study of repaired RC columns subjected to uniaxial and biaxial horizontal loading and variable axial load with longitudinal reinforcement welded steel bars solutions
... horizontal load path definition, many questions can be open in this topic, especially those associated with the response dependency of the load paths as observed by several authors [4,5,7], however in the ...
16
J. Appl. Oral Sci. vol.23 número1
... Also, especially in the linguo-buccal load case, a recorded stress level in elastomers is approaching the material elastic limit, approximately 10 MPa. This stress absorption by elastomers in the interfaces ...
7
(São Paulo, online) vol.3 número3
... Association between body composition and load Body mass was significantly correlated with load in all exercises for both genders. The same phenomenon was observed for lean body mass, but in this case, only ...
8
Compressive fatigue in titanium dental implants submitted to fluoride ions action
... In the present experimental model, this overload by flexion occurred due to the 30–degree angle in which the implant was placed. This produced a moment of flexion at the time of axial load application. This axial ...
6