[PDF] Top 20 Etching time evaluation on the shear bond strength of two adhesive systems in primary teeth
Has 10000 "Etching time evaluation on the shear bond strength of two adhesive systems in primary teeth" found on our website. Below are the top 20 most common "Etching time evaluation on the shear bond strength of two adhesive systems in primary teeth".
Etching time evaluation on the shear bond strength of two adhesive systems in primary teeth
... to (RUC) em dentes decíduos. Metodologia: 48 molares decíduos, hígidos, doados pelo Banco de dentes da USP, foram seccionados longitudinalmente (mésio-distal) e embutidos em resina epóxica, deixando as superfíci- es V ou ... See full document
9
Comparison of two self-etching primers and effect of saliva contamination on shear bond strength of orthodontic brackets
... during the bonding procedure is a common cause of bracket bond ...primer in one component, self-etching primers (SEP) reduce the working time and the risk of ... See full document
7
Effects of thermomechanical and thermocycling on the shear bond strength of brackets to bovine enamel bonded with conventional and self-etching adhesive systems
... matter, the shearing test for this group was performed two days after bracket bonding, which may explain the resistance increase reported ...before. The aim of the ... See full document
9
Tensile bond strength of self-etching versus total-etching adhesive systems under different dentinal substrate conditions
... embedded in epoxy resin and randomly divided into nine groups of ten teeth ...each. The regions of interest for adhesion were demarked in each sample using a glue paper mask with ... See full document
6
Bond strength of adhesive systems to human tooth enamel
... Abstract: The purpose of this study was to evaluate in vitro three adhesive systems: a total etching single-component system (G1 Prime & Bond ...SE Bond), and a ... See full document
6
Shear Bond Strength of Different Adhesive Systems on Enamel Prepared by Er: YAG LASER
... failures in the enamel only present at the LASER treated specimens suggests that LASER promotes rupture due to the micro‐explosions that can weaken enamel, originating heterogenic surfaces as ... See full document
8
Effect of two erosive protocols using acidic beverages on the shear bond strength of orthodontic brackets to bovine enamel
... assess the short-term effect of two in vitro erosive challenge protocols on the bond strength of metal orthodontic brackets on bo- vine ...to ... See full document
9
Effect of shear bond strength of metallic orthodontic brackets bonded with and without dental adhesive
... Objective: The aim of this study was to evaluate the shear bond strength (SBS) of two materials for bonding orthodontic brackets on dental enamel before and ... See full document
8
Influência da profundidade dentinária na resistência à microtração de sistemas adesivos de condicionamento ácido total e autocondicionante = Influence of dentin depth on microtensile bond strength of total etching and self-etching adhesive systems
... Methods: The occlusal surface of twenty sound human molars was sectioned in two levels: 1mm (SD) and 3mm (DD) below the ...cusps. The teeth were divided into four groups: ... See full document
6
Shear resistance evaluation on the enamel surface of deciduous teeth following acid etching with or without previous air abrasion
... from the dental surface. The adhesive system Scotchbond Multi Purpose and Z100 composite resin was applied on both experimental ...groups. The Student’s t test de- monstrated significant ... See full document
6
Effect of pre-etching on in vitro enamel bond strength of two adhesive systems: universal vs. self-etch
... that of phosphoric acid-etch enamel (Gordan et ...that the etching pattern of self-etch adhesives was not as well-defined as that of total- etch adhesives both on ground enamel ... See full document
44
In vitro analysis of shear bond strength and adhesive remnant index comparing light curing and self-curing composites
... avaliar in vitro a resistência ao cisalhamento de compósitos autopolimerizáveis (Concise e Alpha Plast) e fotopolimerizáveis (Transbond XT e Natural Ortho) utilizados na colagem de braquetes metálicos da marca ... See full document
6
Evaluation of Survival Time of Tooth Color Dental Materials in Primary Anterior Teeth
... Introduction: In restorative dentistry, selecting the proper material is an important factor for clinical ...success. The objective of this study was clinical evaluation of ... See full document
8
Activation Mode Effects on the Shear Bond Strength of Dual-cured Resin Cements
... for the factors “resin cement” (p<0.0001), “mode of activation” ...“testing time” ...among the factors. Comparisons according to the Tukey’s test are present- ed in Tables 2 ... See full document
7
Effect of different etching time on the bond strength of ZLS ceramic / Efeito de diferentes tempos de condicionamento na resistência de união da cerâmica ZLS
... As fatias de cerâmica foram fixadas com resina epóxi a tubos de PVC preenchidos com resina acrílica e, foi utilizado uma fita (Imperial, 3M, Sumare, Brazil) com 4 perfurações (aprox. 1 mm de diâmetro) para delimitar a ... See full document
10
Nd:YAG laser influence on bond strength of adhesive resin to dentin
... had the lowest mean μTBS values compared to the other two adhesive ...with the dentin, without the need for previous acid etching as when using Adper Single Bond 2 ... See full document
11
Effect of root perforations on the bond strength of fiberglass post using different adhesive systems and resin cement
... Single Bond 2; G2: sem perfuração + Clearfil SE Bond; G3: com perfuração + Adper™ Single Bond 2; G4: com perfuração + Clearfil SE ...Single Bond 2 promoveu os maiores valores de resistência de ... See full document
9
Effect of mangosteen peel extract as an antioxidant agent on the shear bond strength of orthodontic brackets bonded to bleached teeth
... Introduction: The number of patients who seek orthodontic treatment that may have a history of tooth bleaching is increasing over the ...influence the decrease of the ... See full document
7
The effect of an additional layer of adhesive in dentin bond strength of a universal adhesive system in self-etch mode
... In the present study a micro-tensile test was perform to assess the resin-dentin bond strength of the studied ...Although the ultimate test method for the ... See full document
60
Effect of diode laser irradiation on the bond strength of polymerized non- simplified adhesive systems after 12 months of water storage
... after bond application (AB)], and time [initial (I) and after 12 months of water storage (12 ...performed in the contact mode perpendicular to the dental surface over an ... See full document
7
temas relacionados