[PDF] Top 20 J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
Has 10000 "J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2" found on our website. Below are the top 20 most common "J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2".
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... In addition, a new approach for the numerical simulation of the Light Resin Transfer Molding (LRTM) process was developed in this work, demonstrating the viability of com[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... It can be concluded that increasing the burning time increases the emission, because during the combustion process the material releases its emission.. Effect of Densification.[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... proposed by Smith et al. (1982, 1987) for the mixture of gases and soot. Although these correlations have been proved to be outdated, as discussed in Galarça et al. (2008), they continue to be extensively employed in ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... Table 2 shows the values of the natural frequency, damping factor and half bandwidth of the vibratory system with different rubber hardness and preload conditions[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... The heat generated in its length (7 m) is dissipated by heat transfer to the water for the submersed length (3 m) and also through the natural convection in the an[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... Inverse dynamics control (Sciavicco and Siciliano, 2005; Spong and Vidyasagar, 2006) is an approach to nonlinear control design whose central idea is to construct an inner loop control b[r] ... See full document
12
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... In the present work we present a comparison of the solutions obtained for the direct radiative transfer problem in one-dimensional homogeneous and gray participating media wi[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... Section III provides a brief description of the Boundary Element Method, discusses the numerical model used in this work, and presents its validation based on the[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... In this paper some shallow water solutions found in the literature are compared with numerical simulations that use the complete motion equations (without the sha[r] ... See full document
12
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... Therefore, Web Service technology serves the needs of federative management of data, enabling data of partial models to become accessible in real time and to be [r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... Thus, for the first time, it is shown that, b-parameter from the peak amplitude distribution of AE signal, skewness and kurtosis for statistical distribution and [r] ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... Despite the changes in the roughness parameters and friction coefficient during the pitting tests, the values of maximum contact stress do not show significant changes e[r] ... See full document
10
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... The numerical results for the axial buckling of CNTs are derived and the proposed beam model based on nonlocal boundary conditions is validated through comparison wit[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número2
... The first period is one of slow rate of growth (controlled by the effect of interfacial tension), the second period is one in which the bubble reaches its maximum radiu[r] ... See full document
12
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número4
... Quick stop devices (QSD) are a research instrument developed for investigating the plastic deformation in the workpiece material and on the surface between tool and chip[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número1
... Normal flux percentage mean error on face 4 versus Peclet number, for a boundary element mesh with one hundred and sixty elements, for example 1.. Fortunately, part[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número3
... In this paper, genetic algorithm based artificial neural network hybrid prediction model is proposed to foretell surface roughness and tool wear.. A multiple object[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número1
... The condition 1G also presented full penetration, but the root of the weld has shown dropout (liquid flow) due to the excessive power. Since the resulting microstructure i[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número1
... The centralized cross position between grinding wheel and specimen is associated with the Y-axis of the grinding machine so that the procedure receives the name ZEROY AUT[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.34 número4
... Since reliability analysis using the First Order Reliability Method (FORM) is an optimization procedure itself, RBDO (in its classical version) is a double-loop strategy: the reliabil[r] ... See full document
9
temas relacionados