[PDF] Top 20 J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
Has 10000 "J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2" found on our website. Below are the top 20 most common "J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2".
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... In this work a comparative study of the bilinear dynamic identification of a helicopter blade aeroelastic response is carried out using artificial neural networks is presented.. Two n[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... In the equation, the diffusion coefficient depends whether the considered region is the liquid, interface or solid. The system of equations resulting from the integration of the differential equations is solved by the ... See full document
13
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... Transmission loss of a simple expansion chamber using an extended tube length of 0.1 mm; TMM results (dashed line) and experimental results (solid line).. Figure 6 shows comparisons fo[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... Time averaged radial profiles of solid’s phase axial velocity for different solid’s phase dynamic viscosities 3.4 m above entrance compared to the experimental data of Luo (1987) (Cabe[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... The richness of rhythms related to natural processes, together with nonlinear characteristics of nature, points to the chaotic behavior as a typical response of biological systems.. Pr[r] ... See full document
13
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... Using an error synthesization model obtained by means of homogeneous transformations, each component of the volumetric error can be described as the sum of different parts that are rel[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... The optimization problem concerning with simple transfers (no rendezvous) between coplanar orbits will be formulated as a Mayer problem of optimal control by using Cartesian elements as stated variables. At time t, the ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... Slow strain rate and constant load tests are widely used on stress corrosion cracking research as the basic experimental technique to promote the incidence of cracking and to determine[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... So the way is paved for a complete robot calibration system encompassing modeling, data acquisition from measurements, parameter identification and model compensation, bringing about [r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... Fenili, A., Souza, L.C.G., Góes, L.C.S., Balthazar, J. M., “Investigation of Resonance on a Harmonically Forced Non-Linear Slewing Beam”, AIAC 2003 - Australian International Aerospace Congress (incorporating the ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... Brazilian territory is situated on an intraplate region with low seismic activity, and so, it is important to answer an old question that remains unanswered: “Should standard building [r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... This band can be ascribed to the optical band of the amorphous silicon (a-Si) and is indicative that the machining took place in the ductile mode. According to previous[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... In tube drawing with fixed plug both the outer diameter and the inner diameter of the tube are properly defined if correct process conditions are chosen for th[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... In the present work, the least- squares finite element method (LSFEM), Jiang (1998), has been implemented for simulation of laminar, transitional and turbulent fluid flows using veloci[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... For simultaneous refinement, carried out through Eqs. from (25) to (27), it has been shown that it is possible to reduce the true discretization error (E) using the same set of numerical solutions used to ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... Considering the reduced number of studies evaluating the influence of specimen dimensions on contraction stress development, as well as the discrepancies found among authors regarding[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... As one may observe from experimental Deformation- Temperature curves (under constant loads), the greater the prescribed strain, the higher the load under which the phase transformation[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número1
... Results obtained with microthermocouples (Hohl and Auracher, 2000; Hohl, 1999) let us furthermore assume that at wall superheats beyond CHF the two-phase structure at a given wall supe[r] ... See full document
22
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... The methodology for calculating the flow with separation in aerodynamic bodies, including the viscous effects, is based on two computational codes 1) The potential[r] ... See full document
12
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Figure 13 shows this generated irregular wave pattern (input) and the performance of (a) an anchored platform and platforms equipped with three different DPS controllers: (b) PID[r] ... See full document
7
temas relacionados