[PDF] Top 20 Lat. Am. j. solids struct. vol.11 número11

... Latin American Journal of Solids and Structures 11 (2014) 1886-1905 In ANSYS PLANE 82 elements are used. A concentration keypoint is generated at the crack tip. KCALC command is used for determination of ... See full document

... Latin American Journal of Solids and Structures 11 (2014) 1983-1998 tained through model updating processes. At first, the experimental FRFs of the metal parts are obtained by implementing impact hammer ... See full document

... Latin American Journal of Solids and Structures 11 (2014) 2073-2098 has been used for distribution of electric potential along the thickness. The Hamilton’s principle and Maxwell’s equation were considered ... See full document

... In the first example, the natural frequency ω for the 3 bending modes of a simply supported homo- geneous shaft for different rotating speed Ω are compared with those available in the literature to verify the present ... See full document

... of Solids and Structures 11 (2014) 1999-2017 such cases an alternative ALE method was developed in which the mesh does not necessary fol- lows the ... See full document

... An analytical model is developed in this paper for sound transmission across a thick-walled orthotropic cylindrical shell, based on the third-order shear deformation theory (TSDT). The [r] ... See full document

... Kapuria, S. and Yasin, M.Y., (2010). Active vibration control of piezoelectric laminated beams with electroded actu- ators and sensors using an efficient finite element involving an electric node. Smart Mater. ... See full document

... of Solids and Structures 11 (2014) 1924-1940 cal shells with explosive impact, and it can be seen that the axial cylindrical shell deformation be- tween ... See full document

... Tavakoli H.R, Lotfi O, Soleimani S, Falahtabar Shiade M, Prediction of Energy Absorption Capability in Fiber Reinforced Self-Compacting Concrete Containing Nano-Silica Par[r] ... See full document

... Figure 11, in the initial penetration stage, the projectile highly compress the composite plate which lead to shear/cut loading conditions formed at the edge of ... See full document

... Just like pervious section, the entire simulation steps are done with this kind of fault and in Figure 25, pure signal of angular position, lateral position of axis and linear accelerat[r] ... See full document

... The failure modes of the RSW of advanced high-strength steels were investigated by Abadi and Pouranvari (2014) under tensile- shear, coach-peel and cross-tension tests. Their results sh[r] ... See full document

... The required ductility of a connection is a function of its application. For instance, a lower duc- tility is required for a structure in a low-seismic zone compared to those located in high seismic zones. The structural ... See full document

... Figure 11 shows the Pareto fronts of PCF against SEA for double circular foam filled tubes un- der five different impact angles. In addition, two objective SEA and PCF conflict with each other for all design ... See full document

... The predicted results of triaxial test of sand and sand-silt mixtures with different fine content, which has a good agreement with the results of laboratory tests, suggest that the pro[r] ... See full document

... A fifth-order shear and normal deformation theory is developed in the present study for the static bending and elastic buckling of FG beam. The theory shows fifth-order variation of axi[r] ... See full document

... Figure 11(a), the maximum rail deflection from slab to ballasted tracks in the absence of auxiliary rails is suddenly increased, which is the same for all the vehicle loads and nearly ...Figure 11(b) shows ... See full document

... The results and the reference values proposed by ABNT-NBR 7480 (2007) are shown in.. It must be considered that the surface conformation coefficients were calculated by consid- ering the[r] ... See full document

... Geometrically non-linear analysis of functionally graded material (FGM) plates and shells using a four-node quasi-conforming shell element.. A continuum based three-dimensional shell el[r] ... See full document

... Automobile rollovers considerably contribute to deathful driving accidents. In about 11 million accidents in passenger car, SUV, pickup and vans in 2010, only 3 percent of the accidents were re- lated to the ... See full document