[PDF] Top 20 MATERIAL AND MET HODS Charac terizati on of the area
Has 10000 "MATERIAL AND MET HODS Charac terizati on of the area" found on our website. Below are the top 20 most common "MATERIAL AND MET HODS Charac terizati on of the area".
MATERIAL AND MET HODS Charac terizati on of the area
... evaluate the energy efficiency of a center pivot irrigation system operating in a terrain of variable ...Values of Pumping Energy Efficiency (PEE), Supply Energy Efficiency (SEE), Global ... See full document
9
MATERIAL AND MET HODS
... based on high resolution image analysis. The VisiSize Portable P15 image particle analyzer was used (Oxford Lasers, Imaging Division, Oxford, ...method, the characterization is carried out in real ... See full document
6
MATERIAL AND MET HODS
... between the applied flo w rates for the nutrient distribution in the ...in the layer ...rate of 3.5 L h -1 , corroborating the water distribution ...that the distribution ... See full document
8
MATERIAL AND MET HODS
... (FS) and rear slippage of the tractor (RS) was not affected by the fertilization and intercropping systems (Table 4), being in some treatments, below the recommended standard for ... See full document
7
MATERIAL AND MET HODS
... shows the distribution of soil classes in the peanut areas on the plan formed by the first two principal co mponents (PC1 and PC2) and coded according to the ... See full document
7
MATERIAL AND MET HODS System over vie w
... to the animal and received the data transmitted by the mobile base ...consisted of a Xbee Series 2 radio frequency transceiver (Digi International ...when the adapter was ... See full document
7
MATERIAL AND MET HODS
... depends on the sampling configuration and characteristics associated with the georeferenced phenomenon, such as geometric ...determine the influence of the sampling design ... See full document
10
MATERIAL AND MET HODS Place of study
... For the calibration, were used hermetically sealed bags filled with sand previously dried in drying oven of hot air circulating at 60 °C for 48 ...For the measurement of known masses, a ... See full document
9
MATERIAL AND MET HODS
... i.e. the first 120 days after transplanting (DAT), the water depth was the same for all t ...then on, the Kc values varied approximately between ...to the end of ... See full document
11
MATERIAL AND MET HODS
... pressure, and sweat production (Shen & Zhu, ...cramps and exhaustion have also been reported (Zheng et ...conditions of cold stress also cause health problems (McMichael et ...Indexes of ... See full document
7
MATERIAL AND MET HODS
... For the co mposition of the effective operational cost - EOC (Table 07), the labor expense was considered from the work of two emp loyees in the agricultural operations ... See full document
8
Determinants and Consequences of the Website Perceived Value
... To the commercial website, telepresence is the equivalent of general and internal ...Lombard and Ditton (1997) and Shith (1998), the telepresence concept is used to ... See full document
13
Value-Added Business Based On Small Scale Of Fisheries A Case Study On Nortern And Shouthern Coasts Of Java Lamongan And Pelabuhanratu Regency Indonesia
... development of fisheries sector was expected to keep the economy growth stable, to absorb more labor forces, to produce high foreign exchange, and the most important thing is to increase ... See full document
6
Effect Of Shape And Plan Configuration On Seismic Response Of Structure
... i.e. the plan area for each structure is same only there is difference of ...types of structure total numbers of storeys are 12.The elevation is same for all the 9 ... See full document
5
Distributions of grain parameters on the surface of aircraft engine turbine blades
... In the quality assurance system for components cast using the lost wax method, the object of evaluation is the grain size on the surface of the ...evaluating ... See full document
6
Statistical Assessment of the Effect of Chemical Composition on Mechanical Properties of Hypereutectic AlSi17CuNiMg Silumin
... assessment of the effect of chemical composition on mechanical properties of hypereutectic AlSi17 silumin, which is expected to act as a counterpart of alloys used by automotive ... See full document
4
Evaluating the influence of selected parameters on sensitivity of a numerical model of solidification
... from the NuscaS system [10], which is used for simulating thermomechanical phenomena in solidifying ...upon the heat conduction equation with a source term, solved using enthalpy formulation of ... See full document
6
SOCIAL ECONOMY – A FORM OF INCLUSION AND OF ''REACTIVATING'' OF LABOR IN THE CONTEXT OF THE CURRENT CRISIS
... through the ideologization of the values , of the contempt for the real, productive work represents a major ...in the world set the objective – within the ... See full document
13
Filtration of aluminum alloys and its influence on mechanical properties and shape of eutectical silicium
... perform the test a load source (ZD 10/90, no. 46/79) has been used. The test was conducted in accordance with STN 42 ...result of this test, the variable Rm ( tensile strength ) and A6 ... See full document
4
On The Impact Of Pressure Drop On Human Body With Mathematical Models
... for the impact of pressure drop on the human body has been investigated in the present ...studies. The studies has been aimed at personnel (army and mountaineer) who would ... See full document
3
temas relacionados