[PDF] Top 20 J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
Has 10000 "J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4" found on our website. Below are the top 20 most common "J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4".
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Basically, our two main concerns are: (i) to experimentally investigate the influence of the separation region on the behaviour of the mean and turbulent velocity fiel[r] ... See full document
16
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... In tube drawing with fixed plug both the outer diameter and the inner diameter of the tube are properly defined if correct process conditions are chosen for th[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... By introducing a virtual chain concept in order to close open kinematic chains it is shown that the differential kinematics of serial manipulators can be calculated using[r] ... See full document
12
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... By the determination of the size and location of the venting orifices it was established that the satellite compartment should have its internal pressure equalised so fa[r] ... See full document
4
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... The larger area of contact with the producer layer also yields a more complex interaction between the reservoir and the well, thus parameters influencing horizont[r] ... See full document
6
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Tosaka, N., Kakuda, K. 1986, “Numerical Solution of Steady incompressible Viscous Flow Problems by the Integral Equation Method”. In: Shaw. R. P., Periaux, J., Chaudouet, A., Wu, J., Marino, C., Brebbia, ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... This band can be ascribed to the optical band of the amorphous silicon (a-Si) and is indicative that the machining took place in the ductile mode. According to previous[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... For simultaneous refinement, carried out through Eqs. from (25) to (27), it has been shown that it is possible to reduce the true discretization error (E) using the same set of numerical solutions used to ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Figure 13 shows this generated irregular wave pattern (input) and the performance of (a) an anchored platform and platforms equipped with three different DPS controllers: (b) PID[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Since the supply pressure, the flow coefficient of the valve and the cushioning factor are experimental data, one can observe that the dynamic model employed describes sa[r] ... See full document
11
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... The idea was to determine the distribution of temperature, heat flux, thermal gradient, cooling curves in the cast metal, and heating or/and cooling in the molds d[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Using a pattern classifier implemented by neural networks it is possible to classify patterns of ultrasonic signals from welds by the pulse echo technique and by the TOFD tec[r] ... See full document
5
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... The method described here is thus suited to radiative transfer problems characterized by different layer types and with a left boundary condition expressed as a [r] ... See full document
13
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Moussaoui, F., 2003, “A unified approach for inviscid compressible and nearly incompressible flow by least squares finite element method” Applied Numerical Mathematics, Vol 44, pp.183-[r] ... See full document
9
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... In particular, Prado (2002) studied the perturbation in a lunar satellite for direct orbits and the lifetimes of orbits around the natural satellites of the Solar System. In[r] ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... and its specific heat is c = 480.0 J/kg K (Incropera & DeWitt, 1998). The cylinder dimensions are b = 5.0 m and a = 5.0 m. Figure 2 shows the boundary conditions of the problem. The trivial one- dimensional ... See full document
8
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número4
... Zárate, L.E.; Helman H. e Gálvez, J.M., 1998c, "Um Método para Linearização de Modelos Utilizando Redes Neurais e sua Aplicação em Processos de Laminação". VIII Congreso Latinoamericano de Control ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... In this article the invariance of the Novozhilov's mean rotation measures will be emphasize by the invariance of the determinant of the gradient of deformation tensor of continuum mech[r] ... See full document
3
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número3
... As one may observe from experimental Deformation- Temperature curves (under constant loads), the greater the prescribed strain, the higher the load under which the phase transformation[r] ... See full document
7
J. Braz. Soc. Mech. Sci. & Eng. vol.27 número2
... In the equation, the diffusion coefficient depends whether the considered region is the liquid, interface or solid. The system of equations resulting from the integration of the differential equations is solved by the ... See full document
13
temas relacionados