[PDF] Top 20 Lat. Am. j. solids struct. vol.13 número16

... Previous work of Min et al. (2011) observed the mechanical properties of steel in polar condi- tions. Material type GL-DH32, GL-DH36, and GL-EH36 were taken into consideration. These ma- terials can be used as a defined ... See full document

... Values of the maximum loads (a limit point in the equilibrium path) in each case are shown in Tables 4 to 7. In groups for which a value is missing means that a maximum in the path was not found, i.e. micro-buckling did ... See full document

... It should be noted that in a comparison between results there exists a small difference in the re- sults from the present method and those reported in Ryuet al. (1994). Destabilizing effect of shear degrees of freedom ... See full document

... Rectangular micro-plate, Strain gradient theory, Buckling analysis, Functionally graded, Kirchhoff plate theory, Navier solution.. Navier Solution for Buckling Analysis of Size-Dependen[r] ... See full document

... Nevertheless, when comparing the responses of the TSE specimens with those of the solid TSS tubes the peak forces and the specific energy absorbed are at least 4 times smaller, though [r] ... See full document

... Figure 13, the bottom center of the vehicle contacted the end ...Figure 13, vehicle roll angle and the velocity were approximately 50 degrees and 92 kph, ... See full document

... To mention a few, one can point out to the effect of composite bone structure, geometry and property of the mandible on stress distribution in the cor- tical and cancellous bones, the e[r] ... See full document

... The contribution and novelty of the present work is the use of integral equations (solved numer- ically by the Boundary Element Method) to study the effects of seismic actions in offshor[r] ... See full document

... In this section, a new method is developed to find the trade-off design considering three objective functions, including the first natural frequency, the second natural frequency and the total mass. These quantities are ... See full document

... To the best of the author’s knowledge, the dynamic stability of rotating cantilever wings subjected to inclined follower forces by using the geometrically exact fully intrinsic beam eq[r] ... See full document

... 2- Plane sections remains plane after bending (Euler-Bernoulli Bending Theory). 3- The neutral axis of the hull cross section changed as the collapse of individual structur[r] ... See full document

... In this example, the proposed model is applied to investigate the influence of a thin viscoelastic interphase on the relaxation of the homogenized axial shear stiffness of a periodic fi[r] ... See full document

... It is worth to mention that based on the values given in Figs. 12-13 and 27-28, for all values of H r , zero radial and tangential stresses occur both in radial and transverse directions. The locations of zero ... See full document

... Based on the implemented studies, the proposed method was shown to have a very good performance in terms of the input tracking, disturbances rejectionand robustness against uncertainty[r] ... See full document

... Higher order frequencies are more sensitive to rigidity losses than lower order, thus while the second frequency almost remains unchanged for l = 1 and d 2 = 250 in the range of d[r] ... See full document

... Examination of fractured surfaces (SEM) after testing showed an evidence of adhesive deformation for the joints at higher failure load. 2) The strength variations with respect to the su[r] ... See full document

... In the present context, we do not intend to characterize all possible vibrational modes of the nonlinear bubble oscillatory motion, as done in previous works (Malvar, 2014). Our goal is[r] ... See full document

... Generally, the rigidity of a pile is considerably higher than the ground soil. Thus, the pile body can obstruct the horizontal displacement transfer of the soil between piles for its shielding effect, with the result ... See full document

... Asada, H., (1984). Dynamic analysis and design of robot manipulators using inertia ellipsoids. Proceedings of the IEEE International Conference on Robotics and Automation, Atlanta, USA, 13-15 March1984, pp. ... See full document

... Campos, W. R. C., Rabello E. G., Mansur, T. R., Scaldaferri, D. H. B., Paula, R. G. Souto, J. P. R. S. and Carvalho Júnior I. T., Residual Stress Measurements in the Dissimilar Metal Weld in Pressurizer Safety ... See full document